SAM3S1B Atmel Corporation, SAM3S1B Datasheet - Page 428

• Manufacturer Part Number: SAM3S1B
• Manufacturer: Atmel Corporation

Specifications of SAM3S1B

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 23
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 10
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

428
SAM3S
(MUL + 1)/DIV. When MUL is written to 0, the PLL is disabled and its power consumption is
saved. Re-enabling the PLL can be performed by writing a value higher than 0 in the MUL field.
Whenever the PLL is re-enabled or one of its parameters is changed, the LOCK (LOCKA,
LOCKB) bit in PMC_SR is automatically cleared. The values written in the PLLCOUNT field
(PLLACOUNT, PLLBCOUUNT) in CKGR_PLLR (CKGR_PLLAR, CKGR_PLLBR) are loaded in
the PLL counter. The PLL counter then decrements at the speed of the Slow Clock until it
reaches 0. At this time, the LOCK bit is set in PMC_SR and can trigger an interrupt to the pro-
cessor. The user has to load the number of Slow Clock cycles required to cover the PLL
transient time into the PLLCOUNT field.
The PLL clock can be divided by 2 by writing the PLLDIV2 (PLLADIV2, PLLBDIV2) bit in
PMC_MCKR register.
It is forbidden to change 4/8/12 MHz Fast RC oscillator, or main selection in CKGR_MOR regis-
ter while Master clock source is PLL and PLL reference clock is the Fast RC oscillator.
The user must:
• Switch on the Main RC oscillator by writing 1 in CSS field of PMC_MCKR.
• Change the frequency (MOSCRCF) or oscillator selection (MOSCSEL) in CKGR_MOR.
• Wait for MOSCRCS (if frequency changes) or MOSCSELS (if oscillator selection changes) in
• Disable and then enable the PLL (LOCK in PMC_IDR and PMC_IER register).
• Wait for PLLRDY.
• Switch back to PLL.
PMC_IER.
6500C–ATARM–8-Feb-11