SAM3S1B Atmel Corporation, SAM3S1B Datasheet - Page 715

• Manufacturer Part Number: SAM3S1B
• Manufacturer: Atmel Corporation

Specifications of SAM3S1B

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 23
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 10
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

33.7.8.10
33.7.8.11
33.7.9
To prevent any single software error that may corrupt USART behavior, certain address spaces can be write-protected by
setting the WPEN bit in the USART Write Protect Mode Register (US_WPMR).
If a write access to the protected registers is detected, then the WPVS flag in the USART Write Protect Status Register
(US_WPSR) is set and the field WPVSRC indicates in which register the write access has been attempted.
The WPVS flag is reset by writing the USART Write Protect Mode Register (US_WPMR) with the appropriate access key,
WPKEY.
The protected registers are:
6500C–ATARM–8-Feb-11
6500C–ATARM–8-Feb-11
•
•
•
•
•
•
•
“USART Mode Register”
“USART Baud Rate Generator Register”
“USART Receiver Time-out Register”
“USART Transmitter Timeguard Register”
“USART FI DI RATIO Register”
“USART IrDA FILTER Register”
“USART Manchester Configuration Register”
Write Protection Registers
Local Loopback Mode
Remote Loopback Mode
Local loopback mode connects the output of the transmitter directly to the input of the receiver,
as shown in
the receiver and the TXD pin is continuously driven high, as in idle state.
Figure 33-43. Local Loopback Mode Configuration
Remote loopback mode directly connects the RXD pin to the TXD pin, as shown in
The transmitter and the receiver are disabled and have no effect. This mode allows bit-by-bit
retransmission.
Figure 33-44. Remote Loopback Mode Configuration
Figure
33-43. The TXD and RXD pins are not used. The RXD pin has no effect on
Transmitter
Transmitter
Receiver
Receiver
1
1
RXD
TXD
RXD
TXD
SAM3S
SAM3S
Figure
33-44.
715
715