SAM3S1B Atmel Corporation, SAM3S1B Datasheet - Page 816

• Manufacturer Part Number: SAM3S1B
• Manufacturer: Atmel Corporation

Specifications of SAM3S1B

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 23
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 10
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

35.14.2
Name:
Address:
Access:
This register can only be written if the WPEN bit is cleared in
• CLKDIV: Clock Divider
High Speed MultiMedia Card Interface clock (MCCK or HSMCI_CK) is Master Clock (MCK) divided by (2*(CLKDIV+1)).
• PWSDIV: Power Saving Divider
High Speed MultiMedia Card Interface clock is divided by 2
Warning: This value must be different from 0 before enabling the Power Save Mode in the HSMCI_CR (HSMCI_PWSEN
bit).
• RDPROOF Read Proof Enable
Enabling Read Proof allows to stop the HSMCI Clock during read access if the internal FIFO is full. This will guarantee data
integrity, not bandwidth.
0 = Disables Read Proof.
1 = Enables Read Proof.
• WRPROOF Write Proof Enable
Enabling Write Proof allows to stop the HSMCI Clock during write access if the internal FIFO is full. This will guarantee data
integrity, not bandwidth.
0 = Disables Write Proof.
1 = Enables Write Proof.
• FBYTE: Force Byte Transfer
Enabling Force Byte Transfer allow byte transfers, so that transfer of blocks with a size different from modulo 4 can be
supported.
Warning: BLKLEN value depends on FBYTE.
0 = Disables Force Byte Transfer.
1 = Enables Force Byte Transfer.
816
PDCMODE
31
23
15
7
SAM3S
HSMCI Mode Register
PADV
30
22
14
HSMCI_MR
0x40000004
Read-write
6
FBYTE
29
21
13
5
WRPROOF
28
20
12
4
BLKLEN
BLKLEN
CLKDIV
(PWSDIV)
“HSMCI Write Protect Mode Register” on page
RDPROOF
+ 1 when entering Power Saving Mode.
27
19
11
3
26
18
10
2
PWSDIV
25
17
9
1
6500C–ATARM–8-Feb-11
840.
24
16
8
0