SAM3S4B Atmel Corporation, SAM3S4B Datasheet - Page 307

• Manufacturer Part Number: SAM3S4B
• Manufacturer: Atmel Corporation

Specifications of SAM3S4B

• Flash (kbytes): 256 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 23
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 10
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 48
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

19. Fast Flash Programming Interface (FFPI)
19.1
19.2
19.2.1
Figure 19-1. SAM3SxA (48 bits) Parallel Programming Interface
Figure 19-2. SAM3SxB/C (64/100 pins) Parallel Programming Interface
6500C–ATARM–8-Feb-11
Description
Parallel Fast Flash Programming
Device Configuration
The Fast Flash Programming Interface provides parallel high-volume programming using a stan-
dard gang programmer. The parallel interface is fully handshaked and the device is considered
to be a standard EEPROM. Additionally, the parallel protocol offers an optimized access to all
the embedded Flash functionalities.
Although the Fast Flash Programming Mode is a dedicated mode for high volume programming,
this mode is not designed for in-situ programming.
In Fast Flash Programming Mode, the device is in a specific test mode. Only a certain set of pins
is significant. The rest of the PIOs are used as inputs with a pull-up. The crystal oscillator is in
bypass mode. Other pins must be left unconnected.
MODE[3:0]
MODE[3:0]
DATA[15:0]
0 - 50MHz
0 - 50MHz
DATA[7:0]
NVALID
NVALID
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
VDDIO
NCMD
NCMD
GND
GND
NOE
NOE
RDY
RDY
PGMD[15:0]
TST
PGMEN0
PGMEN1
PGMEN2
PGMNCMD
PGMRDY
PGMNOE
PGMNVALID
PGMM[3:0]
XIN
TST
PGMEN0
PGMEN1
PGMEN2
PGMNCMD
PGMRDY
PGMNOE
PGMNVALID
PGMM[3:0]
XIN
PGMD[7:0]
VDDCORE
VDDIO
VDDPLL
GND
VDDCORE
VDDIO
VDDPLL
GND
SAM3S
307