SAM7S512 Atmel Corporation, SAM7S512 Datasheet - Page 132
SAM7S512
Manufacturer Part Number
SAM7S512
Description
Manufacturer
Atmel Corporation
Specifications of SAM7S512
Flash (kbytes)
512 Kbytes
Pin Count
64
Max. Operating Frequency
55 MHz
Cpu
ARM7TDMI
Hardware Qtouch Acquisition
No
Max I/o Pins
32
Ext Interrupts
32
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
1
Twi (i2c)
1
Uart
3
Ssc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
64
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
3.0 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
3
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
- Current page: 132 of 284
- Download datasheet (2Mb)
Debug Interface
5.4
5.4.1
5-10
ARM7TDMI core clock domains
Clock switch during debug
The ARM7TDMI clocks are described in Clocks on page 5-2.
This section describes:
•
•
When the ARM7TDMI processor enters debug state, it switches automatically from
MCLK to DCLK, it then asserts DBGACK in the HIGH phase of MCLK. The switch
between the two clocks occurs on the next falling edge of MCLK. This is shown in
Figure 5-4.
The core is forced to use DCLK as the primary clock until debugging is complete. On
exit from debug, the core must be allowed to synchronize back to MCLK. This must be
done by the debugger in the following sequence:
1.
2.
The core now automatically resynchronizes back to MCLK and starts fetching
instructions from memory at MCLK speed.
See Exit from debug state on page B-26.
Clock switch during debug on page 5-10
Clock switch during test on page 5-11.
The final instruction of the debug sequence is shifted into the data bus scan chain
and clocked in by asserting DCLK.
RESTART is clocked into the TAP instruction register.
DBGACK
Copyright © 1994-2001. All rights reserved.
MCLK
DCLK
ECLK
Figure 5-4 Clock switching on entry to debug state
Multiplexer
switching point
ARM DDI 0029G
Related parts for SAM7S512
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: