SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 33

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

9.4.6
9.4.7
Table 9-1.
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
User and System Mode
ARM9EJ-S Operating Modes
ARM9EJ-S Registers
R10
R11
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
ARM9TDMI Modes and Registers Layout
Minimum interrupt latency is maintained across both ARM state and Java state. Since byte
codes execution can be restarted, an interrupt automatically triggers the core to switch from
Java state to ARM state for the execution of the interrupt handler. This means that no special
provision has to be made for handling interrupts while executing byte codes, whether in hard-
ware or in software.
In all states, there are seven operation modes:
Mode changes may be made under software control, or may be brought about by external inter-
rupts or exception processing. Most application programs execute in User Mode. The non-user
modes, known as privileged modes, are entered in order to service interrupts or exceptions or to
access protected resources.
The ARM9EJ-S core has a total of 37 registers.
Table 9-1
Supervisor Mode
• User mode is the usual ARM program execution state. It is used for executing most
• Fast Interrupt (FIQ) mode is used for handling fast interrupts. It is suitable for high-speed data
• Interrupt (IRQ) mode is used for general-purpose interrupt handling
• Supervisor mode is a protected mode for the operating system
• Abort mode is entered after a data or instruction prefetch abort
• System mode is a privileged user mode for the operating system
• Undefined mode is entered when an undefined instruction exception occurs
• 31 general-purpose 32-bit registers
• 6 32-bit status registers
application programs
transfer or channel process
R10
R11
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
shows all the registers in all modes.
Abort Mode
R10
R11
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
Undefined Mode
R10
R11
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
Interrupt Mode
R10
R11
R0
R1
R2
R3
R4
R5
R6
R7
R8
R9
Fast Interrupt Mode
SAM9G35
SAM9G35
R10_FIQ
R11_FIQ
R8_FIQ
R9_FIQ
R0
R1
R2
R3
R4
R5
R6
R7
33
33