SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 652

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

34.14.12 HSMCI Status Register
Name:
Address:
Access:
• CMDRDY: Command Ready
0 = A command is in progress.
1 = The last command has been sent. Cleared when writing in the HSMCI_CMDR.
• RXRDY: Receiver Ready
0 = Data has not yet been received since the last read of HSMCI_RDR.
1 = Data has been received since the last read of HSMCI_RDR.
• TXRDY: Transmit Ready
0= The last data written in HSMCI_TDR has not yet been transferred in the Shift Register.
1= The last data written in HSMCI_TDR has been transferred in the Shift Register.
• BLKE: Data Block Ended
This flag must be used only for Write Operations.
0 = A data block transfer is not yet finished. Cleared when reading the HSMCI_SR.
1 = A data block transfer has ended, including the CRC16 Status transmission.
the flag is set for each transmitted CRC Status.
Refer to the MMC or SD Specification for more details concerning the CRC Status.
• DTIP: Data Transfer in Progress
0 = No data transfer in progress.
1 = The current data transfer is still in progress, including CRC16 calculation. Cleared at the end of the CRC16 calculation.
• NOTBUSY: HSMCI Not Busy
This flag must be used only for Write Operations.
A block write operation uses a simple busy signalling of the write operation duration on the data (DAT0) line: during a data
transfer block, if the card does not have a free data receive buffer, the card indicates this condition by pulling down the data
line (DAT0) to LOW. The card stops pulling down the data line as soon as at least one receive buffer for the defined data
transfer block length becomes free.
The NOTBUSY flag allows to deal with these different states.
652
652
CSTOE
UNRE
31
23
15
–
7
–
SAM9G35
SAM9G35
OVRE
DTOE
30
22
14
HSMCI_SR
0xF0008040 (0), 0xF000C040 (1)
Read-only
–
6
–
ACKRCVE
NOTBUSY
DCRCE
CSRCV
29
21
13
5
SDIOWAIT
ACKRCV
RTOE
DTIP
28
20
12
4
XFRDONE
RENDE
BLKE
27
19
11
–
3
FIFOEMPTY
RCRCE
TXRDY
26
18
10
–
2
DMADONE
RXRDY
RDIRE
25
17
9
–
1
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
SDIOIRQA
BLKOVRE
CMDRDY
RINDE
24
16
8
0