SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 857

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

39.7.8.18
39.7.9
11053B–ATARM–22-Sep-11
11053B–ATARM–22-Sep-11
Test Modes
Bus Idle Time-out
The user can choose by the WKUPTYP bit in the LIN Mode register (US_LINMR) either to send
a LIN 2.0 wakeup request (WKUPTYP=0) or to send a LIN 1.3 wakeup request (WKUPTYP=1).
A wake-up request is transmitted by writing the Control Register (US_CR) with the LINWKUP bit
to 1. Once the transfer is completed, the LINTC flag is asserted in the Status Register (US_SR).
It is cleared by writing the Control Register (US_CR) with the RSTSTA bit to 1.
If the LIN bus is inactive for a certain duration, the slave nodes shall automatically enter in sleep
mode. In the LIN 2.0 specification, this time-out is fixed at 4 seconds. In the LIN 1.3 specifica-
tion, it is fixed at 25000 Tbits.
In Slave Node configuration, the Receiver Time-out detects an idle condition on the RXD line.
When a time-out is detected, the bit TIMEOUT in the Channel Status Register (US_CSR) rises
and can generate an interrupt, thus indicating to the driver to go into sleep mode.
The time-out delay period (during which the receiver waits for a new character) is programmed
in the TO field of the Receiver Time-out Register (US_RTOR). If the TO field is programmed to
0, the Receiver Time-out is disabled and no time-out is detected. The TIMEOUT bit in US_CSR
remains to 0. Otherwise, the receiver loads a 17-bit counter with the value programmed in TO.
This counter is decremented at each bit period and reloaded each time a new character is
received. If the counter reaches 0, the TIMEOUT bit in the Status Register rises.
If STTTO is performed, the counter clock is stopped until a first character is received.
If RETTO is performed, the counter starts counting down immediately from the value TO.
Table 39-16. Receiver Time-out programming
The USART can be programmed to operate in three different test modes. The internal loopback
capability allows on-board diagnostics. In the loopback mode the USART interface pins are dis-
connected or not and reconfigured for loopback internally or externally.
LIN Specification
2.0
1.3
19 200 bit/s
20 000 bit/s
Baud Rate
1 000 bit/s
2 400 bit/s
9 600 bit/s
-
Time-out period
25 000 Tbits
4s
SAM9G35
SAM9G35
38 400
76 800
80 000
25 000
4 000
9 600
TO
857
857