SAM9G10 Atmel Corporation, SAM9G10 Datasheet - Page 916

• Manufacturer Part Number: SAM9G10
• Manufacturer: Atmel Corporation

Specifications of SAM9G10

• Flash (kbytes): 0 Kbytes
• Pin Count: 217
• Max. Operating Frequency: 266 MHz
• Cpu: ARM926
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 96
• Ext Interrupts: 96
• Usb Transceiver: 3
• Usb Speed: Full Speed
• Usb Interface: Host, Device
• Spi: 2
• Twi (i2c): 1
• Uart: 4
• Ssc: 3
• Sd / Emmc: 1
• Graphic Lcd: Yes
• Video Decoder: No
• Camera Interface: No
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: NO
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.08 to 1.32
• Fpu: No
• Mpu / Mmu: No/Yes
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

41.6.3
41.6.4
Figure 41-3. EOCx and DRDY Flag Behavior
916
(ADC_CHSR)
(ADC_SR)
(ADC_SR)
EOCx
DRDY
CHx
SAM9G35
Conversion Resolution
Conversion Results
Write the ADC_CR
with START = 1
The ADC supports 8-bit or 10-bit resolutions. The 8-bit selection is performed by setting the
LOWRES bit in the ADC Mode Register (ADC_MR). By default, after a reset, the resolution is
the highest and the DATA field in the data registers is fully used. By setting the LOWRES bit, the
ADC switches to the lowest resolution and the conversion results can be read in the lowest sig-
nificant bits of the data registers. The two highest bits of the DATA field in the corresponding
ADC_CDR register and of the LDATA field in the ADC_LCDR register read 0.
When a conversion is completed, the resulting 10-bit digital value is stored in the Channel Data
Register (ADC_CDRx) of the current channel and in the ADC Last Converted Data Register
(ADC_LCDR). By setting the TAG option in the ADC_EMR, the ADC_LCDR presents the chan-
nel number associated to the last converted data in the CHNB field.
The channel EOC bit in the Status Register (ADC_SR) is set and the DRDY is set. In the case of
a connected DMA channel, DRDY rising triggers a data transfer request. In any case, either
EOC and DRDY can trigger an interrupt.
Reading one of the ADC_CDR registers clears the corresponding EOC bit. Reading ADC_LCDR
clears the DRDY bit and EOC bit corresponding to the last converted channel.
If the ADC_CDR is not read before further incoming data is converted, the corresponding Over-
run Error (OVREx) flag is set in the Overrun Status Register (ADC_OVER).
Likewise, new data converted when DRDY is high sets the GOVRE bit (General Overrun Error)
in ADC_SR.
The OVREx flag is automatically cleared when ADC_OVER is read, and GOVRE flag is auto-
matically cleared when ADC_SR is read.
Read the ADC_CDRx
Write the ADC_CR
with START = 1
Read the ADC_LCDR
11053B–ATARM–22-Sep-11