AD9963 Analog Devices, AD9963 Datasheet - Page 29

• Manufacturer Part Number: AD9963
• Description: 10-/12-Bit, Low Power, Broadband MxFE
• Manufacturer: Analog Devices

Specifications of AD9963

• Resolution (bits): 12bit
• Throughput Rate: 100MSPS
• # Chan: 2
• Supply V: Multi(+1.8Anlg, +1.8Dig),Multi(+1.8Anlg, +3.3Dig) ,Single(+1.8),Single(+3.3)
• Sample Rate: 100MSPS
• Adc Bits X #adcs-speed: 12x2-100 MHz
• Dac Bits X #dacs-clkspeed: 12x2-170 MHz
• Pkg Type: CSP
• Primary Application: Broadband Wireless

Register Name
DAC10BMSBs
DAC10BLSBs
DAC10A Config
DAC10A MSBs
DAC10A LSBs
TX BIST Control
RX BIST Control
Register
Address
0x46
0x47
0x48
0x49
0x4A
0x50
0x51
Bit(s)
1:0
7:0
7:2
1:0
7
6:5
4:2
1:0
7:0
7:2
1:0
7:5
4
3
2
1
0
7:5
4
3
2
Parameter
DAC10B_RNG[1:0]
DAC10B[9:2]
Unused
DAC10B[1:0]
DAC10A_EN
Unused
DAC10A_TOP[2:0]
DAC10A_RNG[1:0]
DAC10A[9:2]
Unused
DAC10A[1:0]
Unused
TX_PTTRN
TX_INSEL
TX_CONT
TX_START
TX_BISTEN
Unused
RX_PTTRN
RX_INSEL
RX_CONT
Rev. 0 | Page 29 of 60
Function
010: 2.0 V.
011: 2.5 V.
100: 3.0 V.
The total range of the DAC extends from top-of-range, to top-of-range
minus the span. The span is set as:
00: 2.0 V.
01: 1.5 V.
10: 1.0 V.
11: 0.5 V.
DAC10B voltage control word (eight most significant bits).
DAC10Bvoltage control word (two least significant bits).
0: powers down DAC10A.
1: enables DAC10A.
Sets the DAC output voltage at the top range as follows:
000: 1.0 V.
001: 1.5 V.
010: 2.0 V.
011: 2.5 V.
100: 3.0 V.
The total range of the DAC extends from top-of-range to top-of-range
minus the span. The span is set as:
00: 2.0 V.
01: 1.5 V.
10: 1.0 V.
11: 0.5 V.
DAC10A voltage control word (eight most significant bits).
DAC10A voltage control word (two least significant bits).
Unused
Chooses the pattern type for the BIST sequence.
0: selects checker board pattern (0xA5A, 0x5A5, 0xA5A, …).
1: selects PRN output.
0: selects pattern input from internal pattern generator.
1: selects pattern from the external pins of the Tx port.
0: runs the BIST for 512 cycles.
1: runs the BIST continuously.
0: keep the BIST engine in an idle state.
1: start the BIST sequence.
0: disable the BIST engine.
1: enable the BIST engine.
Chooses the pattern type for the BIST sequence.
0: selects checker board pattern (0xA5A, 0x5A5, 0xA5A, …).
1: selects PRN output.
0: selects pattern input from internal pattern generator.
1: selects pattern from the external pins of the Rx path.
0: runs the BIST for 512 cycles.
1: runs the BIST continuously.
AD9961/AD9963