ADP8863 Analog Devices, ADP8863 Datasheet - Page 28

• Manufacturer Part Number: ADP8863
• Description: Charge Pump, 7-Channel Fun Lighting LED Driver
• Manufacturer: Analog Devices

Specifications of ADP8863

• Vin Range: 2.5 to 5.5V
• Vout (v): 4.3 to 5.5
• Synchronous: No
• Package: 20-Lead LFCSP,20-Lead WLCSP
• Led Configuration: Parallel
• Topology: Capacitive
• I2c Support: Yes
• Max Iout (ma): 60mA
• Brightness Control: I2C
• Peak Efficiency (%): 89%
• Switching Frequency: 1.32MHz
• Over Volt Protection (v): 5V

ADP8863
Mode Control Register 2 (MDCR2)—Register 0x02
Table 13. MDCR2 Bit Map
Bit 7
Table 14. Bit Descriptions for the MDCR2 Register
Bit Name
N/A
SHORT_INT
TSD_INT
OVP_INT
CMP2_INT
CMP_INT
1
Interrupt Enable (INTR_EN)—Register 0x03
Table 15. INTR_EN Bit Map
Bit 7
Table 16. Bit Descriptions for the INTR_EN Register
Bit Name
N/A
SHORT_IEN
TSD_IEN
OVP_IEN
CMP2_IEN
CMP_IEN
Interrupt bits are cleared by writing a 1 to the flag; writing a 0 or reading the flag has no effect.
Bit 6
Bit 6
Reserved
Reserved
Bit No.
[7:5]
4
3
2
1
0
Bit No.
[7:5]
4
3
2
1
0
Description
Reserved.
Short-circuit interrupt is enabled. When the SHORT_INT status bit is set after an error condition, an interrupt is
raised to the host if the SHORT_IEN flag is enabled.
1 = the short-circuit interrupt is enabled.
0 = the short-circuit interrupt is disabled (the SHORT_INT flag continues to assert).
Thermal shutdown interrupt is enabled. When the TSD_INT status bit is set after an error condition, an interrupt is
raised to the host if the TSD_IEN flag is enabled.
1 = the thermal shutdown interrupt is enabled.
0 = the thermal shutdown interrupt is disabled (the TSD_INT flag continues to assert).
Overvoltage interrupt enabled. When the OVP_INT status bit is set after an error condition, an interrupt is raised to
the host if the OVP_IEN flag is enabled.
1 = the overvoltage interrupt is enabled.
0 = the overvoltage interrupt is disabled (the OVP_INT flag continues to assert).
When the CMP2_INT status bit is set after an enabled comparator trips, an interrupt is raised if the CMP2_IEN flag is
enabled.
1 = the second phototransistor comparator interrupt is enabled.
0 = the second phototransistor comparator interrupt is disabled (the CMP2_INT flag continues to assert).
When the CMP_INT status bit is set after an enabled comparator trips, an interrupt is raised if the CMP_IEN flag is
enabled.
1 = the main comparator interrupt is enabled.
0 = the main comparator interrupt is disabled (the CMP_INT flag continues to assert).
Bit 5
Bit 5
Description
Reserved.
Short-circuit error interrupt.
1 = a short-circuit or overload condition on VOUT has been detected.
0 = no short-circuit or overload condition has been detected.
Thermal shutdown interrupt.
1 = the device temperature has exceeded 150°C (typical).
0 = no overtemperature condition has been detected.
Overvoltage interrupt.
1 = VOUT has exceeded V
0 = VOUT has not exceeded V
1 = the second ALS comparator (CMP_IN2) has changed state.
0 = the second sensor comparator has not been triggered.
1 = main ALS comparator (CMP_IN) has changed state.
0 = the main sensor comparator has not been triggered.
Bit 4
SHORT_INT
Bit 4
SHORT_IEN
1
OVP
Rev. A | Page 28 of 52
Bit 3
TSD_INT
.
Bit 3
TSD_IEN
OVP
.
Bit 2
OVP_INT
Bit 2
OVP_IEN
Bit 1
CMP2_INT
Bit 1
CMP2_IEN
Bit 0
CMP_INT
Bit 0
CMP_IEN