ADP225 Analog Devices, ADP225 Datasheet - Page 19
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
ADP225
Manufacturer Part Number
ADP225
Description
Dual, 300 mA Adjustable Output, QOD, Low Noise, High PSRR Voltage Regulator
Manufacturer
Analog Devices
Datasheet
1.ADP222.pdf
(24 pages)
Data Sheet
ENABLE FEATURE
The
enable and disable the VOUTx pins under normal operating
conditions. Figure 67 shows a rising voltage on ENx crossing
the active threshold, where V
voltage on ENx crosses the inactive threshold, V
As shown in Figure 67, the ENx pins have built-in hysteresis.
This prevents on/off oscillations that can occur due to noise on
the ENx pins as it passes through the threshold points.
The active/inactive thresholds of the ENx pins are derived from
the VIN voltage. Therefore, these thresholds vary with changing
input voltage. Figure 68 shows typical ENx active/inactive thresholds
when the input voltage varies from 2.5 V to 5.5 V.
The
start to limit the inrush current when the output is enabled. The
start-up time for the 2.8 V option is approximately 240 µs from
the time the ENx active threshold is crossed to when the output
reaches 90% of its final value. The start-up time is somewhat
dependent on the output voltage setting and increases slightly as
the output voltage increases.
1.2
1.0
0.8
0.6
0.4
0.2
ADP222/ADP223/ADP224/ADP225
ADP222/ADP223/ADP224/ADP225
0
2.3
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
ENx FALL
ENx RISE
0.5
Figure 68. Typical Enable Thresholds vs. Input Voltage
V
2.7
IN
Figure 67. Typical ENx Pin Operation, V
= 5.5V
0.6
3.1
0.7
3.5
ENABLE VOLTAGE (V)
V
0.8
IN
3.9
OUTx
(V)
turns on. When a falling
0.9
4.3
1.0
4.7
use the ENx pins to
use an internal soft
IN
= 5.5 V
1.1
5.1
OUTx
turns off.
5.5
1.2
Rev. B | Page 19 of 24
PARALLELING OUTPUTS TO INCREASE OUTPUT
CURRENT
The
reference voltage for each LDO. The reference voltages are
trimmed to plus or minus a couple of millivolts of each other.
This allows paralleling of the LDOs to increase the output
current to 600 mA. The adjust pins of each LDO are tied
together and a single output voltage divider sets the output
voltage. Even though the output voltage of each LDO is slightly
different, at high load currents, the resistance of the package
and the board layout absorbs the difference. Figure 70 shows
the schematic of a typical application where the LDO outputs
are paralleled.
QUICK OUTPUT DISCHARGE (QOD) FUNCTION
The
force the voltage on each output to zero when the respective
LDO is disabled. This ensures that the outputs of the LDOs are
always in a well-defined state, regardless if it is enabled or not.
The
function. Figure 71 compares the turn-off time of a 3.3 V output
LDO with and without the QOD function. Both LDOs have a
1 kΩ resistor connected to each output. The LDO with the
QOD function discharges the output to 0 V in less than 1 ms,
whereas the 1 kΩ load takes over 5 ms to do the same.
ADP224/ADP225
ADP223
ADP222/ADP223
OFF
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
V
Figure 70. Paralleling Outputs for Higher Output Current
0
IN
ON
= 3.3V
ADP222/ADP223/ADP224/ADP225
ENx
3.3V
2.8V
1.8V
1.2V
100
/
+ C1
ADP225
1µF
200
Figure 69. Typical Start-Up Time
1
2
3
4
300
EN1
EN2
GND
ADJ2
include an output discharge resistor to
use a single band gap to generate the
do not include the output discharge
400
TIME (µs)
500
VOUT1
VOUT2
ADJ1
VIN
600
8
7
6
5
700
R2
R1
VOUT2 = 2.8V
800
+ C2
1µF
900
1000