P89LPC915_916_917 NXP Semiconductors, P89LPC915_916_917 Datasheet - Page 32
P89LPC915_916_917
Manufacturer Part Number
P89LPC915_916_917
Description
The P89LPC915/916/917 are single-chip microcontrollers, available in low-cost packages,based on a high performance processor architecture that executes instructions in two tofour clocks, six times the rate of standard 80C51 devices
Manufacturer
NXP Semiconductors
Datasheet
1.P89LPC915_916_917.pdf
(75 pages)
- Current page: 32 of 75
- Download datasheet (363Kb)
NXP Semiconductors
P89LPC915_916_917_5
Product data sheet
8.6 External clock input option
8.7 CCLK wake-up delay
8.8 CCLK modification: DIVM register
In this configuration, the processor clock is derived from an external source driving the
CLKIN pin. The rate may be from 0 Hz up to 18 MHz.
When using an external clock input frequency above 12 MHz, the reset input
function of P1.5 must be enabled. An external circuit is required to hold the device
in reset at power-up until V
removed V
an external clock input frequency above 12 MHz, in some applications, an external
brownout detect circuit may be required to hold the device in reset when V
below the minimum specified operating voltage.
The P89LPC915/916/917 has an internal wake-up timer that delays the clock until it
stabilizes. The delay is 224 OSCCLK cycles plus 60 s to 100 s.
The OSCCLK frequency can be divided down up to 510 times by configuring a dividing
register, DIVM, to generate CCLK. This feature makes it possible to temporarily run the
CPU at a lower rate, reducing power consumption. By dividing the clock, the CPU can
retain the ability to respond to events that would not exit Idle mode by executing its normal
program at a lower rate. This can also allow bypassing the oscillator start-up time in cases
where Power-down mode would otherwise be used. The value of DIVM may be changed
by the program at any time without interrupting code execution.
Fig 11. Block diagram of oscillator control
OSCILLATOR
(7.3728 MHz)
OSCILLATOR
WATCHDOG
CLKIN
(400 kHz)
RC
DD
GENERATOR
BAUD RATE
will fall below the minimum specified operating voltage. When using
RCCLK
Rev. 05 — 15 December 2009
8-bit microcontrollers with accelerated two-clock 80C51 core
DD
UART
has reached its specified level. When system power is
RCCLK
XCLK
TIMERS 1 AND 0
DIVM
peripheral clock
P89LPC915/916/917
OSCCLK
I
2
2
C
RTCS1:0
CCLK
PCLK
(P89LPC916)
SPI
ADC1/DAC1
© NXP B.V. 2009. All rights reserved.
WDT
CPU
RTC
CLKOUT
002aaa831
DD
32 of 75
falls
Related parts for P89LPC915_916_917
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-bit microcontrollers with accelerated two-clock 80C51 core 2 kB 3 V Flash with 8-bit A/D converter
Manufacturer:
PHILIPS [NXP Semiconductors]
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2420/2460 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2458 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2468 microcontroller around a 16-bit/32-bitARM7TDMI-S CPU core with real-time debug interfaces that include both JTAG andembedded trace
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2470 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
NXP Semiconductors designed the LPC2478 microcontroller, powered by theARM7TDMI-S core, to be a highly integrated microcontroller for a wide range ofapplications that require advanced communications and high quality graphic displays
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The Philips Semiconductors XA (eXtended Architecture) family of 16-bit single-chip microcontrollers is powerful enough to easily handle the requirements of high performance embedded applications, yet inexpensive enough to compete in the market for hi
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The XA-S3 device is a member of Philips Semiconductors? XA(eXtended Architecture) family of high performance 16-bitsingle-chip microcontrollers
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP BlueStreak LH75401/LH75411 family consists of two low-cost 16/32-bit System-on-Chip (SoC) devices
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3130/3131 combine an 180 MHz ARM926EJ-S CPU core, high-speed USB2
Manufacturer:
NXP Semiconductors
Datasheet:
Part Number:
Description:
The NXP LPC3141 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3143 combine a 270 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3152 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors
Part Number:
Description:
The NXP LPC3154 combines an 180 MHz ARM926EJ-S CPU core, High-speed USB 2
Manufacturer:
NXP Semiconductors