XA-H4 NXP Semiconductors, XA-H4 Datasheet - Page 8

• Manufacturer Part Number: XA-H4
• Description: The powerful 16-bit XA CPU core and rich feature set make the XA-H3 and XA-H4 devices ideal for high-performance real-time applications such as industrial control and networking
• Manufacturer: NXP Semiconductors

Philips Semiconductors
PIN DESCRIPTIONS
1999 Sep 24
See Pins 56, 57 for 2 additional Chip Selects
BHE_CASH
CS1_RAS1
CS2_RAS2
CS3_RAS3
BLE_CASL
Mnemonic
A19 – A0
D15 – D0
XTALOut
Single-chip 16-bit microcontroller
ResetIn
XTALIn
Size16
ClkOut
WAIT/
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
P0.6
P0.7
V
CS0
V
WE
OE
SS
DD
1, 19, 28,
2, 20, 29,
Pin No.
24 – 21,
42 – 30,
27 – 25
44, 59,
43, 62,
18 – 3
76, 88
77, 89
Lqfp
100
55
52
60
61
49
48
47
46
50
51
54
53
45
90
91
92
93
94
95
99
Type
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
O
O
O
O
O
O
O
I
I
I
I
I
I
Ground: 0 V reference.
Power Supply: This is the power supply voltage for normal, idle, and power down operation.
Reset: A low on this pin resets the microcontroller, causing I/O ports and peripherals to take on
their default states, and the processor to begin execution at the address contained in the reset
vector.
Wait/Size16: During Reset, this input determines bus size for boot device (“1” = 16-bit boot
device; “0” = 8-bit.) During normal operation this is the Wait input (“1” = Wait; “0” = Proceed.)
Crystal 1: Input to the inverting amplifier used in the oscillator circuit and input to the internal
clock generator circuits.
Crystal 2: Output from the oscillator amplifier.
Chip Select 0: This output provides the active low chip select to the boot device (usually ROM or
Flash.) It cannot be connected to DRAM. From reset, it is enabled and mapped to an address
range based at 000000h. It can be remapped by software to a higher base in the address map
(see the “Memory Interface” chapter in the XA-H4 User Manual .)
Chip Select 1 or RAS1: Chip Selects and RAS 1 through 5 come out of reset disabled. They can
be programmed to function as normal chip selects, or as RAS strobes to DRAM. CS1 can be
“swapped” with CS0 (see the SWAP operation and control bit in the “Memory Controller” chapter
of the XA-H4 User Manual .) CS1 is usually mapped to be based at 000000h after the swap, but is
capable of being based anywhere in the 16 MB space.
Chip Select 2 or RAS2: Active low Chip Selects CS1 through CS5 come out of reset disabled.
They can be programmed to function as normal chip selects, or as RAS strobes to DRAM. CS2
through CS5 are not used with the “SWAP” operation (see the “Memory Controller” chapter in the
XA-H4 User Manual .) They are mappable to any region of the 16 MB address space.
CS3 or RAS3: See Chip Select 2 for description.
Write Enable: Goes active low during all bus write cycles only.
Output Enable: Goes active low during all bus read cycles only.
Byte Low Enable or CAS_Low_Byte: Goes active low during all bus cycles that access D7 – D0,
read or write, Generic or DRAM. Functions as CAS during DRAM cycles.
Byte High Enable or CAS_High_Byte: Goes active low during all bus cycles that access data
bus lines D15 – D8, read or write, Generic or DRAM. Functions as CAS during DRAM cycles.
Clock Output: This pin outputs a buffered version of the internal CPU clock. The clock output
may be used in conjunction with the external bus to synchronize WAIT state generators, etc. The
clock output may be disabled by software.
WARNING: The capacitive loading on this output must not exceed 40 pf.
Address[19:0]: These address lines output A19 – A0 during (SRAM, etc.) bus cycles.
DRAMS (H4 only) are connected only to pins 22, 21, 18 – 10 (pins A17 to A7; see user manual
“MIF Chapter” for connecting various DRAM sizes); the appropriate address values are
multiplexed onto these 11 pins for RAS and CAS during DRAM bus cycles.
Data[15:0]: Bi-directional data bus, D15 – D0.
P0.0_Sync0_BRG0: Port 0 Bit 0, or USART0 Sync input or output, or USART0 BRG output, or
USART0 TxClk output.
P0.1_RTS0: Port 0 Bit 1, or USART0 RTS (Request To Send) output.
P0.2_CTS0: Port 0 Bit 2, or USART0 CTS (Clear To Send) input.
P0.3_CD0: Port 0 Bit 3, or USART0 Carrier Detect input.
P0.4_TRClk0: Port 0 Bit 4, or USART0 TR clock input.
P0.5_RTClk0: Port 0 Bit 5, or USART0 RT clock input.
P0.6: Port 0 Bit 6
P0.7: Port 0 Bit 7
8
Name and Function
Preliminary specification
XA-H4
Note
See
1, 2
1, 2
1
1
1
1
1
1