STM32F407ZG STMicroelectronics, STM32F407ZG Datasheet - Page 66

• Manufacturer Part Number: STM32F407ZG
• Description: High-performance and DSP with FPU, ARM Cortex-M4 MCU with 1 Mbyte Flash, 168 MHz CPU, Art Accelerator, Ethernet
• Manufacturer: STMicroelectronics

Specifications of STM32F407ZG

• Core: ARM 32-bit Cortex™-M4 CPU with FPU, Adaptive real-time accelerator (ART Accelerator™) allowing 0-wait state execution from Flash memory, frequency up to 168 MHz, memory protection unit, 210 DMIPS/1.25 DMIPS/MHz (Dhrystone 2.1), and DSP instructions
• 3×12-bit, 2.4 Msps A/d Converters: up to 24 channels and 7.2 MSPS in triple interleaved mode
• General-purpose Dma: 16-stream DMA controller with FIFOs and burst support
• Up To 17 Timers: up to twelve 16-bit and two 32-bit timers up to 168 MHz, each with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input
• 10/100 Ethernet Mac With Dedicated Dma: supports IEEE 1588v2 hardware, MII/RMII
• Rtc: subsecond accuracy, hardware calendar

Electrical characteristics
Table 11.
1. The average expected gain in power consumption when VOS = 0 compared to VOS = 1 is around 10% for the whole
2. If an inverted reset signal is applied to PDR_ON, this value can be lowered to 1.7 V when the device operates in a reduced
3. When the ADC is used, refer to
4. If V
5. It is recommended to power V
6. If T
7. In low power dissipation state, T
66/167
Symbol
temperature range, when the system clock frequency is between 30 and 144 MHz.
temperature range (0 to 70 °C).
V
V
V
DDA
CAP1
CAP2
P
T
T
A
REF+
A
D
J
is lower, higher P
can be tolerated during power-up and power-down operation.
pin is present, it must respect the following condition: V
General operating conditions (continued)
When the internal regulator is ON,
V
connect a stabilization capacitor.
When the internal regulator is OFF
(BYPASS_REG connected to V
V
from 1.2 V.
Power dissipation at T
suffix 6 or T
Ambient temperature for 6 suffix
version
Ambient temperature for 7 suffix
version
Junction temperature range
CAP_1
CAP_1
and V
and V
D
values are allowed as long as T
A
Parameter
= 105 °C for suffix 7
CAP_2
CAP_2
DD
Table 65: ADC
A
and V
can be extended to this range as long as T
must be supplied
pins are used to
A
= 85 °C for
DDA
from the same source. A maximum difference of 300 mV between V
characteristics.
DD
Doc ID 022152 Rev 2
(6)
),
J
LQFP64
LQFP100
LQFP144
LQFP176
UFBGA176
Maximum power dissipation
Low power dissipation
Maximum power dissipation
Low power dissipation
6 suffix version
7 suffix version
does not exceed T
DDA
-V
REF+
Conditions
< 1.2 V.
Jmax
J
does not exceed T
.
(7)
(7)
STM32F405xx, STM32F407xx
Jmax
Min
–40
–40
–40
–40
–40
–40
1.1
.
-
-
-
-
-
Max
435
465
500
526
513
105
105
125
105
125
1.3
85
DD
and
Unit
mW
°C
°C
°C
V