STM8AF518A STMicroelectronics, STM8AF518A Datasheet - Page 58

no-image

STM8AF518A

Manufacturer Part Number
STM8AF518A
Description
Automotive 8-bit MCU, with up to 128 Kbytes Flash, EEPROM, 10-bit ADC, timers, LIN, CAN, USART, SPI, I2C, 3 V to 5.5 V
Manufacturer
STMicroelectronics
Datasheet

Specifications of STM8AF518A

Max Fcpu
24 MHz
Program Memory
32 to 128 Kbytes Flash program; data retention 20 years at 55 °C
Data Memory
up to 2 Kbytes true data EEPROM; endurance 300 kcycles
Ram
2 Kbytes to 6 Kbytes
Advanced Control Timer
16-bit, 4 CAPCOM channels, 3 complementary outputs, dead-time insertion and flexible synchronization

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
STM8AF518ATA
Manufacturer:
ST
Quantity:
435
Part Number:
STM8AF518ATA
Manufacturer:
ST
0
Part Number:
STM8AF518ATA/B
Manufacturer:
ST
0
Part Number:
STM8AF518ATAY
Manufacturer:
ST
0
Part Number:
STM8AF518ATB
Manufacturer:
st
Quantity:
30
Part Number:
STM8AF518ATB
Manufacturer:
ST
0
Part Number:
STM8AF518ATBX
Manufacturer:
ST
Quantity:
170
Part Number:
STM8AF518ATBX
Manufacturer:
ST
0
Part Number:
STM8AF518ATBX
Manufacturer:
ST
Quantity:
20 000
Part Number:
STM8AF518ATBX
Manufacturer:
ST
Quantity:
11 334
Electrical characteristics
10.1.5
10.2
58/106
Pin input voltage
The input voltage measurement on a pin of the device is described in
Figure 9.
Absolute maximum ratings
Stresses above those listed as ‘absolute maximum ratings’ may cause permanent damage
to the device. This is a stress rating only and functional operation of the device under these
conditions is not implied. Exposure to maximum rating conditions for extended periods may
affect device reliability.
Table 21.
1. All power (V
2. I
|V
|V
V
Symbol
DDx
DDx
SSx
external power supply
cannot be respected, the injection current must be limited externally to the I
injection is induced by V
pads, there is no positive injection current, and the corresponding V
INJ(PIN)
V
V
ESD
IN
- V
- V
- V
DD
DD
SS
must never be exceeded. This is implicitly insured if V
| Variations between all the different ground pins
| Variations between different power pins
Pin input voltage
Voltage characteristics
DD
Supply voltage (including V
Input voltage on true open drain pins (PE1, PE2)
Input voltage on any other pin
Electrostatic discharge voltage
, V
DDIO
, V
IN
DDA
> V
) and ground (V
DD
while a negative injection is induced by V
Doc ID 14395 Rev 8
Ratings
V
IN
DDA and
SS
(2)
, V
SSIO
V
DDIO
, V
SSA
STM8A pin
)
(1)
) pins must always be connected to the
IN
maximum is respected. If V
STM8AF52/62xx, STM8AF51/61xx
IN
(2)
maximum must always be respected
see
V
V
IN
INJ(PIN)
SS
SS
< V
Min
-0.3
(electrical sensitivity) on
Absolute maximum ratings
- 0.3
- 0.3
SS
. For true open-drain
value. A positive
Figure
page 86
V
DD
Max
6.5
6.5
IN
9.
50
50
+ 0.3
maximum
Unit
mV
V
V

Related parts for STM8AF518A