ST72345C4 STMicroelectronics, ST72345C4 Datasheet - Page 91
ST72345C4
Manufacturer Part Number
ST72345C4
Description
8-bit MCU
Manufacturer
STMicroelectronics
Datasheet
1.ST72344S4.pdf
(247 pages)
Specifications of ST72345C4
Up To 16 Kbytes Program Memory
single voltage extended Flash (XFlash) with readout and write protection, in-circuit and inapplication programming (ICP and IAP). 10K write/erase cycles guaranteed, data retention
256 Bytes Data Eeprom With Readout Protection. 300k Write/erase Cycles Guaranteed, Data Retention
20 years at 55 °C.
Clock Sources
crystal/ceramic resonator oscillators, high-accuracy internal RC oscillator or external clock
5 Power-saving Modes
Slow, Wait, Halt, Auto-wakeup from Halt and Active-halt
16-bit Timer A With
1 input capture, 1 output compares, external clock input, PWM and pulse generator modes
16-bit Timer B With
2 input captures, 2 output compares, PWM and pulse generator modes
- Current page: 91 of 247
- Download datasheet (3Mb)
ST72344xx ST72345xx
Caution:
Table 42.
A modification of the time base is taken into account at the end of the current period
(previously set) to avoid an unwanted time shift. This allows to use this time base as a real-
time clock.
Bit 1 = OIE Oscillator interrupt enable
Bit 0 = OIF Oscillator interrupt flag
The BRES and BSET instructions must not be used on the MCCSR register to avoid
unintentionally clearing the OIF bit.
MCC beep control register (MCCBCR)
Reset value: 0000 0000 (00h)
Bits 7:2 = Reserved, must be kept cleared.
Bits 1:0 = BC[1:0] Beep control
prescaler
This bit set and cleared by software.
0: Oscillator interrupt disabled
1: Oscillator interrupt enabled
This interrupt can be used to exit from Active-halt mode.
When this bit is set, calling the ST7 software HALT instruction enters the Active-halt
power-saving mode
This bit is set by hardware and cleared by software reading the MCCSR register. It
indicates when set that the main oscillator has reached the selected elapsed time
(TB1:0).
0: Timeout not reached
1: Timeout reached
These 2 bits select the PF1 pin beep capability.
Counter
7
0
200000
16000
32000
80000
Time base control
0
.
f
OSC2
0
20 ms
50 ms
4 ms
8 ms
Doc ID 12321 Rev 5
= 4 MHz
0
Read/Write
Time base
0
f
OSC2
10 ms
25 ms
2 ms
4 ms
= 8 MHz
0
On-chip peripherals
BC1
TB1
0
0
1
1
BC0
0
91/247
TB0
0
1
0
1
Related parts for ST72345C4
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet: