DS2433 Maxim, DS2433 Datasheet - Page 21

no-image

DS2433

Manufacturer Part Number
DS2433
Description
The DS2433 4Kb 1-Wire® EEPROM identifies and stores relevant information about the product to which it is associated
Manufacturer
Maxim
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS2433+
Manufacturer:
Maxim Integrated
Quantity:
271
Part Number:
DS2433-Z01
Manufacturer:
Maxim Integrated
Quantity:
497
Part Number:
DS2433AX-S#T
Manufacturer:
Maxim Integrated
Quantity:
282
Part Number:
DS2433AX-S+TW
Manufacturer:
Maxim Integrated
Quantity:
459
Part Number:
DS2433D+&TR
Manufacturer:
XILINX
Quantity:
200
Part Number:
DS2433D/T&R
Manufacturer:
Maxim Integrated
Quantity:
326
Company:
Part Number:
DS2433S
Manufacturer:
MAXIM
Quantity:
429
Part Number:
DS2433S
Manufacturer:
DALLAS
Quantity:
225
Part Number:
DS2433S+
Manufacturer:
Maxim
Quantity:
14 356
Company:
Part Number:
DS2433S+
Manufacturer:
MAXIM
Quantity:
402
Part Number:
DS2433S+T&R
Manufacturer:
MAXIM
Quantity:
1 248
Part Number:
DS2433S+T&R
Manufacturer:
MAXIM
Quantity:
285
Part Number:
DS2433S+TR
Manufacturer:
MAXIM
Quantity:
8 000
Part Number:
DS2433S+TR
Manufacturer:
MAXIM
Quantity:
251
Part Number:
DS2433S-500-00+T&R
Manufacturer:
MAXIM
Quantity:
700
AC ELECTRICAL CHARACTERISTICS—OVERDRIVE SPEED
NOTES:
1) V
2) All voltages are referenced to ground.
3) V
4) Input load is to ground.
5) The Copy Scratchpad takes 5ms maximum during which the voltage on the 1-Wire bus must not fall
6) Capacitance on the data pin could be 800pF when power is first applied. If a 5kresistor is used to
7) During the execution of the Copy Scratchpad command the DS2433 automatically erases the memory
8) The duration of the low pulse sent by the master should be a minimum of 1μs with a maximum value
9) The optimal sampling point for the master is as close as possible to the end time of the t
10) Read data setup time refers to the time the host must pull the 1-Wire bus low to read a bit. Data is
11) An additional reset or communication sequence cannot begin until the reset high time has expired.
12) The reset low time (t
Time Slot
Write 1 Low Time
Write 0 Low Time
Read Low Time
Read Data Valid
Release Time
Read Data Setup
Recovery Time
Reset Time High
Reset Time Low
Presence Detect High
Presence Detect Low
below 2.8V.
pull up the data line to V
normal communications.
locations to be written to. No extra steps need to be taken by the bus master.
as short as possible to allow time for the pullup resistor to recover the line to a high level before the
1-Wire device samples in the case of a write-one time or before the master samples in the case of a
read-one time.
without exceeding t
the pullup resistor to recover to a high level. For a read-zero time slot, it ensures that a read will occur
before the fastest device(s) release the line.
guaranteed to be valid within 1 s of this falling edge.
otherwise, it could mask or conceal interrupt pulses.
PUP
IH
is a function of the external pullup resistor and V
PARAMETER
= external pullup voltage. See Figure 8.
RDV
RSTL
. For the case of a read-one time slot, this maximizes the amount of time for
PUP
) should be restricted to a maximum of 960s, to allow interrupt signaling,
, 5s after power has been applied the parasite capacitance will not affect
SYMBOL
t
t
RELEASE
t
t
PDHIGH
t
t
PDLOW
t
t
t
LOWR
t
LOW1
LOW0
t
RSTH
SLOT
RSTL
RDV
t
REC
SU
21 of 23
MIN
48
48
6
1
6
1
0
1
2
8
PUP
.
TYP
1.5
2
MAX
16
16
80
24
2
2
4
1
6
(T
A
UNITS
= -40C to +85C.)
s
s
s
s
s
s
s
s
s
s
s
s
RDV
NOTES
10
11
DS2433
8
8
9
period

Related parts for DS2433