MAX9108ESD+ Maxim Integrated Products, MAX9108ESD+ Datasheet - Page 6
![IC COMPAR LP QUAD 14-SOIC](/photos/6/57/65727/175-14-soic_sml.jpg)
MAX9108ESD+
Manufacturer Part Number
MAX9108ESD+
Description
IC COMPAR LP QUAD 14-SOIC
Manufacturer
Maxim Integrated Products
Type
General Purposer
Datasheet
1.MAX9109EUTT.pdf
(13 pages)
Specifications of MAX9108ESD+
Number Of Elements
4
Output Type
TTL
Voltage - Supply
4.5 V ~ 5.5 V
Mounting Type
Surface Mount
Package / Case
14-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
25ns, Dual/Quad/Single, Low-Power,
TTL Comparators
Noise or undesired parasitic AC feedback cause most
high-speed comparators to oscillate in the linear region
(i.e., when the voltage on one input is at or near the
voltage on the other input). The MAX9107/MAX9108/
MAX9109 eliminate this problem by incorporating an
internal hysteresis of 2mV. When the two comparator
input voltages are equal, hysteresis effectively causes
one comparator input voltage to move quickly past the
other, thus taking the input out of the region where
oscillation occurs. Standard comparators require that
hysteresis be added through the use of external resis-
tors. The MAX9107/MAX9108/MAX9109’s fixed internal
hysteresis eliminates these resistors. To increase hys-
6
_______________Detailed Description
______________________________________________________________Pin Description
MAX9107
_______________________________________________________________________________________
—
—
—
—
—
—
—
—
—
—
—
1
2
3
7
6
5
8
4
MAX9108
10
14
13
12
—
—
—
11
—
—
1
2
3
7
6
5
8
9
4
PIN
SC70/SOT23
—
—
—
—
—
—
—
—
—
—
—
—
—
1
3
4
6
2
5
MAX9109
Timing
4, 8
SO
—
—
—
—
—
—
—
—
—
—
—
—
7
2
3
1
6
5
NAME
OUTA
OUTB
OUTC
OUTD
teresis and noise margin even more, add positive feed-
back with two resistors as a voltage divider from the
output to the noninverting input.
Adding hysteresis to a comparator creates two trip
points: one for the input voltage rising and one for the
input voltage falling (Figure 1). The difference between
these two input-referred trip points is the hysteresis.
The average of the trip points is the offset voltage.
Figure 1 illustrates the case where IN- is fixed and IN+
is varied. If the inputs were reversed, the figure would
look the same, except the output would be inverted.
The MAX9109 includes an internal latch, allowing the
result of a comparison to be stored. If LE is low, the
latch is transparent (i.e., the comparator operates as
though the latch is not present). The state of the com-
parator output is latched when LE is high (Figure 2).
INC+
IND+
INA+
INB+
GND
INA-
INB-
INC-
IND-
OUT
N.C.
V
IN+
IN-
LE
CC
Channel A Output
Channel A Inverting Input
Channel A Noninverting Input
Channel B Output
Channel B Inverting Input
Channel B Noninverting Input
Channel C Output
Channel C Inverting Input
Channel C Noninverting Input
Channel D Output
Channel D Inverting Input
Channel D Noninverting Input
Output
Noninverting Input
Inverting Input
Positive Supply
Ground
Latch E nab l e. The l atch i s tr ansp ar ent w hen LE i s l ow .
No Connection. Not internally connected.
FUNCTION