LMH0031VS/NOPB National Semiconductor, LMH0031VS/NOPB Datasheet - Page 29

no-image

LMH0031VS/NOPB

Manufacturer Part Number
LMH0031VS/NOPB
Description
IC DESER/DESCRAM DGTL VID 64TQFP
Manufacturer
National Semiconductor
Type
Descrambler/Deserializerr
Datasheet

Specifications of LMH0031VS/NOPB

Applications
SDTV/HDTV
Mounting Type
Surface Mount
Package / Case
64-TQFP, 64-VQFP
Input Voltage
3.3 V
Supply Voltage (max)
3.45 V
Supply Voltage (min)
3.15 V
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
For Use With
SD131EVK - BOARD EVALUATION LMH0031
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
*LMH0031VS
*LMH0031VS/NOPB
LMH0031VS

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LMH0031VS/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
Application Information
output timing practices, especially critical at HD data rates.
The power pins feeding the I/O should have low inductance
connections to the power and ground planes. It is recom-
mended that these connections use at least two vias per
power or ground pin. Short interconnecting traces consistent
with good layout practices and soldering rules must be used.
Sampling or clocking of data by external devices should be
so timed as to take maximum advantage of the steady-state
portion of the parallel output data interval. The LMH0031 is
designed so that video data will be stable at the positive-
going transition of V
to the data transition intervals associated with the negative-
going clock edge. The specified propagation delay and clock
to data timing parameters must be observed. When data is
being sampled from the video data port together with the
ANC port and/or I/O port, it is recommended that the sam-
pling clocks be synchronized with the video clock, V
minimize possible effects from ground bounce or output
droop on sampled signal levels.
PROCESSING NON-SUPPORTED RASTER FORMATS
The number and type of HD raster formats has proliferated
since the LMH0031 was designed. Though not specifically
capable of fully or automatically processing these new for-
mats, the LMH0031 may still be capable of deserializing
them. The user is encouraged to experiment with processing
these formats, keeping in mind that the LMH0031 has not
been tested to handle formats other than those detailed in
Table 4. Therefore, the results from attempts to process
non-supported formats is not guaranteed. The following
guidelines concerning device setup are provided to aid the
user in configuring the LMH0031 to attempt limited process-
ing of these other raster formats.
In general, the device is configured to defeat its automatic
format detection function and to limit operation to a general
CLK
. Data should not be sampled close
(Continued)
CLK
, to
29
HD format. (The user should consult Table 4 for guidance on
the format groups similar to the non-supported one to be
processed). Since most non-supported formats are in the
HD group, the LMH0031 should be configured to operate in
HD-ONLY mode by setting bit-5 of the FORMAT 0 register
(address 0Bh). Also, the device should be further configured
by loading the FORMAT SET[4:0] bits of this register with the
general HD sub-format code. In addition, since control data
is being written to the port, AD[9:8] must be driven as 11b.
The complete data word for this general HD sub-format code
with HD-ONLY bit set is 33Fh. Since this format differs from
those in the table, the EAV/SAV indicators are disabled.
Without these indicators, line numbering and CRC process-
ing are disabled and ANC data extraction will not function.
Output video chroma and luma data will be word-aligned.
Post-processing of the parallel data output from the
LMH0031 will be needed to implement CRC checking or line
number tracking.
USING EXTERNAL VCXO FOR VCLK
The EXTERNAL V
address 55h) is a special application function which enables
use of an external VCXO as a substitute for the internally
generated V
LMH0031 which provides phase-frequency detection and
control voltage output for the VCXO. An external loop filter
and voltage amplifier are required to interface the control
voltage output to the VCXO frequency control input. When
this function is used, the R
from the bias supply output to the control voltage output of
the phase-frequency detector. The V
function, becoming the input for the VCXO signal.
Figure 7 shows an example using dual VCXOs for V
handle both standard and high definition video.
CLK
. Additional circuitry is enabled within the
CLK
bit of VIDEO CONTROL 0 (register
BB
output function is changed
CLK
output changes
www.national.com
CLK
to

Related parts for LMH0031VS/NOPB