TA8233BHQ Toshiba, TA8233BHQ Datasheet

no-image

TA8233BHQ

Manufacturer Part Number
TA8233BHQ
Description
Manufacturer
Toshiba
Datasheet

Specifications of TA8233BHQ

No. Of Channels
2
Package
HZIP 17-P-2.00
Recommended Vcc (v)
13.2
Rl=2 Ohm
26W x 2
Rl=4 Ohm
19W x 2
Rl=8 Ohm
-
Features/built-in Functions
2 BTL channels, standby switch, clipping/shorting detector
Operating Voltage (v)
9 to 18

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
TA8233BHQ
Manufacturer:
TOSH
Quantity:
1 000
30W BTL × 2ch Audio Power Amplifier
The thermal resistance θj−T of TA8233BHQ package designed for
low thermal resistance, has high efficiency of heat radiation.
The temperature rise of chip can be reduced, and the influence
from the degradation of the features due to the temperature rise
at the high output can also be reduced.
This stereo audio power IC, designed for car audio use, has two
built−in channels to reduce the characteristic difference between
L and R channels. It also contains output short detection circuit,
output clip detection and various kind of protection.
Features
High power
Low thermal resistance: θj−T = 1.5°C / W (infinite heat sink)
Low distortion ratio: THD = 0.04% (typ.)
Low noise: V
Built−in stand−by function
Built−in output clip detection circuit
Built−in output short detection circuit
Built−in various protection circuits
Operating supply voltage: V
: (with pin(4) set at low, power is turned off.) I
: (pin(1): Open collector (active low))
: (pin(9): Open collector (active low))
: Thermal shut down, Over voltage, Out→V
: P
(V
P
(V
P
(V
OUT (2)
OUT (3)
OUT (1)
CC
CC
CC
(V
NO
= 14.4V, f = 1kHz, THD = 10%, R
= 13.2V, f = 1kHz, THD = 10%, R
= 13.2V, f = 1kHz, THD = 10%, R
CC
= 0.30mV
= 26W (typ.) / channel
= 19W (typ.) / channel
= 30W (typ.) / channel
= 13.2V, R
TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic
(V
CC
rms
= 13.2V, f = 1kHz, P
L
CC (opr)
= 4Ω, G
(typ.)
TA8233BHQ
= 9~18V
V
= 50dB, R
L
L
L
CC
OUT
= 2Ω)
= 2Ω)
= 4Ω)
g
SB
= 0Ω, BW = 20Hz~20kHz)
short, Out→GND short and Out−Out short.
= 1W, R
= 1µA (typ.)
1
L
= 4Ω, G
Weight: 9.8g (typ.)
V
= 50dB)
TA8233BHQ
2004-09-28

Related parts for TA8233BHQ

TA8233BHQ Summary of contents

Page 1

... TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic 30W BTL × 2ch Audio Power Amplifier The thermal resistance θj−T of TA8233BHQ package designed for low thermal resistance, has high efficiency of heat radiation. The temperature rise of chip can be reduced, and the influence from the degradation of the features due to the temperature rise at the high output can also be reduced ...

Page 2

... Block Diagram TA8233BHQ (G = 50dB) V Caution And Application Method (description is made only on the single channel.) 1. Voltage gain adjustment This IC has the amplifier constructions as shown in Fig.1. The pre−amp (amp 1) is provided to the primary stage, and the input voltage is amplified by the flat amps, amp 3 and amp 4 of each channel through the phase amp (amp 2). Since the input offset is prevented by pre− ...

Page 3

... Off On 3~V Adjustage of stand−by SW (1) Since V can directly be controlled off by the microcomputer, the switching relay can be omitted. CC (2) Since the control current is microscopic, the switching relay of small current capacity is satisfactory for switching ( increased and BE (V) 0 TA8233BHQ 2004-09-28 ...

Page 4

... NF terminal voltage. Concretely, monitor the output DC voltage and vary the capacity value in input condenser and NF condenser (see Fig.4) (Reference) In case of setting the condition (G setting) reduced or with the feedback amount increased, care must be taken V = 40dB) with R = 470Ω TA8233BHQ 2004-09-28 ...

Page 5

... NPN Tr. is turned on possible to improve the tone quality with the current of flowing into pin(1) and with controlling the volume, tone control circuit through L.P.F smoothing circuit as shown in Fig.5. In case of being unused this function, use this IC as open connection on pin(1). (Application) 5 TA8233BHQ 2004-09-28 ...

Page 6

... V CC (1) The power stage bias circuit is cut. (2) pin(8): Ripple capacitor is rapidly discharged by turning Q3 on and then Q1 and Q2 on. or output to GND short (Application) off CC and the stand−by terminals become high or low CC ≒8V internally on IC TA8233BHQ 2004-09-28 ...

Page 7

... CC Made liable to oscillate. Oscillation allowance For filtering power supply hum and ripple. Large at using AC rectified power supply. Small at using DC power supply. Oscillation allowance improved. Noise reduction 7 TA8233BHQ which makes CC Remarks Larger Than Related to gain. Refer to item 4. →on or off. Refer to item 3. Refer to item 3. ...

Page 8

... — — 600Ω g — 0.775V (0dBm) OUT rms Stand−by→off — (power→on) — 1mA C — 1mA C 8 TA8233BHQ Min. Typ. Max. Unit — 120 250 mA — 30 — — — — 0.04 0 −1 ...

Page 9

... Test Circuit TA8233BHQ (G = 50dB TA8233BHQ 2004-09-28 ...

Page 10

... TA8233BHQ 2004-09-28 ...

Page 11

... TA8233BHQ 2004-09-28 ...

Page 12

... TA8233BHQ 2004-09-28 ...

Page 13

... Package Dimensions Weight: 9.8g (typ.) 13 TA8233BHQ 2004-09-28 ...

Page 14

... The product is often the final stage (the external output stage circuit. Substandard performance or malfunction of the destination device to which the circuit supplies output may cause damage to the circuit or to the product. 14 TA8233BHQ 030619EBF 2004-09-28 ...

Related keywords