TMPM382FSFG Toshiba, TMPM382FSFG Datasheet - Page 124

• Manufacturer Part Number: TMPM382FSFG
• Manufacturer: Toshiba

Specifications of TMPM382FSFG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 64K
• Rom Type: Flash
• Ram (kbytes): 8K
• Number Of Pins: 64
• Package: QFP(14x14)
• Vcc: 5V
• Cpu Mhz: 40
• Ssp (ch) Spi: 1
• I2c/sio (ch): 1
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: N
• Cs/wait Controller (ch): -
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: -
• 12-bit Ad Converter: 10
• 16-bit Timer / Counter: 6
• Motor / Igbt Control: Y
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: Y
• Hardware Cec Controller: -
• Comparators: -
• Low-voltage Detector: Y
• Etm Hardware Trace: 2-bit

8 Input/Output Ports
PDCR
(0x4000_00C4)
PDFR1
(0x4000_00C8)
PDDATA
(0x4000_00C0)
8.2.5
(Important)
TMPM382 (64 pin version) does not implement port D (PD0 to PD6).
Please do not use these functions if you use this product.
specified in units of bits. Besides the general-purpose input/output function, the port D performs the
serial interface function, 16-bit timer input/output, the external interrupt input and encoder input.
pull-down disabled.
register and enable input in the PDIE register. These settings enable the interrupt input even if the
CGSTBYCR<DRVE> bit in the clock/mode control block is set to stop driving of pins during STOP
mode.
(Note)
The port D is a general-purpose, 7-bit input/output port. For this port, inputs and outputs can be
Reset initializes all bits of the port D as general-purpose ports with input, output, pull-up and
To use the external interrupt input for releasing STOP mode, select this function in the PDFR1,PDFR3
Port D (PD0 to PD6)
Bit Symbol
Read/Write
After reset
Function
Bit Symbol
Read/Write
After reset
Function
Bit Symbol
Read/Write
After reset
In modes other than STOP mode, interrupt input is enabled regardless of the PxFR
register setting as long as input is enabled in PxIE. Make sure to disable unused
interrupts when programming the device.
“0” is read.
“0” is read.
“0” is read. 0:PORT
－
R
－
R
0
R
7
7
7
0
-
1:RXD2
PD6F1
PD6C
PD6
6
6
0
6
0
Port D function register 1
TMPM380/M382 - 10 / 52 -
Port D control register
Port D register
0:PORT
1:TXD2
PD5F1
PD5C
PD5
0
0
5
5
5
0:PORT
1:SCLK2
PD4F1
PD4C
PD4
0
0
4
4
4
1: enabled
0: disabled
0:PORT
1:INT9
PD3F1
PD3C
Output
R/W
R/W
R/W
PD3
“0”
0
0
3
3
3
0:PORT
1:ENCZ0
PD2F1
PD2C
PD2
2
2
2
0
0
0:PORT
1:ENCB0
PD1F1
PD1C
TMPM380/M382
PD1
1
1
1
0
0
0:PORT
1:ENCA0
PD0F1
PD0C
PD0
0
0
0
0
0