TMPM382FSFG Toshiba, TMPM382FSFG Datasheet - Page 133

• Manufacturer Part Number: TMPM382FSFG
• Manufacturer: Toshiba

Specifications of TMPM382FSFG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 64K
• Rom Type: Flash
• Ram (kbytes): 8K
• Number Of Pins: 64
• Package: QFP(14x14)
• Vcc: 5V
• Cpu Mhz: 40
• Ssp (ch) Spi: 1
• I2c/sio (ch): 1
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: N
• Cs/wait Controller (ch): -
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: -
• 12-bit Ad Converter: 10
• 16-bit Timer / Counter: 6
• Motor / Igbt Control: Y
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: Y
• Hardware Cec Controller: -
• Comparators: -
• Low-voltage Detector: Y
• Etm Hardware Trace: 2-bit

PHFR1
(0x4000_01C8)
PHDATA
(0x4000_01C0)
PHCR
(0x4000_01C4)
8.2.9
specified in units of bits. Besides the general-purpose input/output function, the port H performs the
analog input of the A/D converter and the external interrupt input.
pull-down disabled.
and enable input in the PHIE register. These settings enable the interrupt input even if the
CGSTBYCR<DRVE> bit in the clock/mode control block is set to stop driving of pins during STOP
mode.
(Note 1) In modes other than STOP mode, interrupt input is enabled regardless of the PxFR
(Note 2) Unless you use all the bits of port H as analog input pins, conversion accuracy may be
The port H is a general-purpose 8-bit input/output port. For this port, inputs and outputs can be
Reset initializes all bits of the port H as general-purpose ports with input, output, pull-up and
To use the external interrupt input for releasing STOP mode, select this function in the PHFR1 register
Port H (PH0 to PH7)
Bit Symbol
Read/Write
After reset
Function
Bit Symbol
Read/Write
After reset
Bit Symbol
Read/Write
After reset
Function
register setting as long as input is enabled in PxIE. Make sure to disable unused
interrupts when programming the device.
reduced. Be sure to verify that this causes no problem on your system.
PH7C
PH7
7
7
7
0
0
-
TMPM380/M382 - 19 / 52 -
PH6C
PH6
6
0
6
6
Port H function register 1
0
-
Port H control register
Port H register
“0” is read
PH5C
PH5
R
5
5
5
0
0
-
PH4C
PH4
4
4
4
0
0
-
0: disabled
1: enabled
Output
R/W
R/W
“0”
PH3C
PH3
3
3
3
0
0
-
0:PORT
1:INT2
PH2F1
PH2C
PH2
2
2
2
0
0
0:PORT
1:INT1
PH1F1
PH1C
TMPM380/M382
R/W
PH1
1
1
1
0
0
0:PORT
1:INT0
PH0F1
PH0C
PH0
0
0
0
0
0