TMPM382FSFG Toshiba, TMPM382FSFG Datasheet - Page 206

no-image

TMPM382FSFG

Manufacturer Part Number
TMPM382FSFG
Description
Manufacturer
Toshiba
Datasheet

Specifications of TMPM382FSFG

Product Summaries
Summary
Lead Free
Yes
Rohs Compatible Product(s)
Available
Rom (kbytes)
64K
Rom Type
Flash
Ram (kbytes)
8K
Number Of Pins
64
Package
QFP(14x14)
Vcc
5V
Cpu Mhz
40
Ssp (ch) Spi
1
I2c/sio (ch)
1
Uart/sio (ch)
3
Usb
-
Can
-
Ethernet
-
External Bus Interface
N
Cs/wait Controller (ch)
-
Dma Controller
2
10-bit Da Converter
-
10-bit Ad Converter
-
12-bit Ad Converter
10
16-bit Timer / Counter
6
Motor / Igbt Control
Y
Real Time Clock
1
Watchdog Timer
Y
Osc Freq Detect
Y
Clock Gear
Y
Low-power Hold Function
-
Remote Control Interface
Y
Hardware Cec Controller
-
Comparators
-
Low-voltage Detector
Y
Etm Hardware Trace
2-bit
10 16-bit Multi-purpose Timers (MPTs)
Note1 : Do not change settings as following registers during timer is in operation (MTnRUN<MTRUN>=”1”).
Note2 : Setting of MTnRG0/1 must be set as “Value of MTnRG0 < Value of MTnRG1”.
Note3 : Setting of MTnRG0/1/2/3/4 must be set as follows;
Note4 : Write to MTnRG0/1/2/3/4 by unit of 16 bits or 32 bits. Writing by units of bytes is prohibited.
Note5: Regardless of the timer operating or stopping, MTOUTn0 and MTOUTn1 output pins change according
Note6: During timer in operation, if IGBT timer restart register MTnIGRESTA<IGRESTA> is set to “1”, timer
Note7: When changing the noise eliminating time setting of IGBT timer trigger start pin (MTnTBIN) specified
Note8:
Note9: If MTnIGCR<IGSTP> is set to “10” (stop counter after completing output in the current period) and
Note10: While timer is stopping, a value of timer counters (MTUCn) is not captured. Since data in the capture
to a setting register of IGBT output control register (MTnIGOCR). Confirm the operating conditions
beforehand when changing the MTnIGOCR setting.
counter can be cleared and restarted. Confirm the operating conditions beforehand when changing the
MTnIGRESTA setting.
with MTnIGCR<IGNCSEL3:0>, timer counter must be stopped. When changing the setting of the
trigger start pin (MTnTBIN) of IGBT timer, the timer must be waited to start (MTnRUN<MTRUN>=”1”)
until noise elimination time (more than specified time for noise elimination) passes after changing
setting of noise elimination time.
MTnIGEMGCR<IGEMGCNT[3:0]>,
(MTnIGEMGCR<IGEMGEN>=”0”).
stopped by MTnRUN<MTRUN>, confirm a period interrupt generation before changing the timer
setting and restart.
register (MTnCP0, MTnCP1) is maintained, a preceding captured value of timer counter can be read.
0 < Value of MTnRG0 < Value of MTnRG1 ≦ Value of MTnIGRG4 ≦ 0xffff
0 < Value of MTnIGRG2 < Value of MTnIGRG3 ≦ Value of MTnIGRG4 ≦ 0xffff
MTnTBFFCR
MTnTBMOD
MTnTBCR
MTnIGCR
MTnIGICR
MTnIGEMGCR
10.4.1.1
When
changing
Operating Precautions for MPTs
the
noise
TMPM380/M382 - 6 / 87 -
eliminating
EMG
protection
setting
of
circuit
GEMGn
must
pin
TMPM380/M382
specified
be
disabled
with

Related parts for TMPM382FSFG