TMPM382FSFG Toshiba, TMPM382FSFG Datasheet - Page 35

• Manufacturer Part Number: TMPM382FSFG
• Manufacturer: Toshiba

Specifications of TMPM382FSFG

• Product Summaries: Summary
• Lead Free: Yes
• Rohs Compatible Product(s): Available
• Rom (kbytes): 64K
• Rom Type: Flash
• Ram (kbytes): 8K
• Number Of Pins: 64
• Package: QFP(14x14)
• Vcc: 5V
• Cpu Mhz: 40
• Ssp (ch) Spi: 1
• I2c/sio (ch): 1
• Uart/sio (ch): 3
• Usb: -
• Can: -
• Ethernet: -
• External Bus Interface: N
• Cs/wait Controller (ch): -
• Dma Controller: 2
• 10-bit Da Converter: -
• 10-bit Ad Converter: -
• 12-bit Ad Converter: 10
• 16-bit Timer / Counter: 6
• Motor / Igbt Control: Y
• Real Time Clock: 1
• Watchdog Timer: Y
• Osc Freq Detect: Y
• Clock Gear: Y
• Low-power Hold Function: -
• Remote Control Interface: Y
• Hardware Cec Controller: -
• Comparators: -
• Low-voltage Detector: Y
• Etm Hardware Trace: 2-bit

6 Clock/Mode Control
<Bit 0><WUEON>
<Bit 1><WUEF>
<Bit 2><PLLON>
<Bit 3><WUPSEL1>
<Bit 8><XEN1>
<Bit 9><XTEN>
<Bit 16><XEN2>
<Bit 17><OSCSEL>
6.2.2.2 Oscillation Control Register (CGOSCCR: 0x4004_0204)
Read/Write
Read/Write
Read/Write
Read/Write
Bit symbol
After reset
Bit symbol
After reset
Bit symbol
After reset
Bit symbol
After reset
Function
Function
Function
Function
Bit1:0 for warm-up counter
value.
If high-speed oscillator is
selected,<Bit15:14><WO
UDR 1:0> is set “0”.
Bit5:2 for warm-up counter value.
WUODR13
Bit13:6 for warm-up counter value.
WUODR1
WUODR5
R/W
15
23
31
7
0
0
0
0
-
: Enables to monitor the status of the warm-up timer.
: Enables to start the warm-up timer.
: Specifies operation of the PLL.
: Select source clock for warm-up timer between high-speed oscillator and
low-speed oscillator. High-speed oscillator is followed by <Bit19><WUPSEL2>.
: Specifies operation of the external high-speed oscillator1.
: Specifies operation of the external low-speed oscillator.
: Specifies operation of the internal high-speed oscillator2.
: High speed oscillator switch from internal oscillator(OSC1) to external
oscillator(OSC2).OFD does not use the feature, after switching the external
oscillator, it is recommended to stop the internal oscillator to reduce power
consumption. Also, after switching to an external oscillator, please not switch to the
internal oscillator.
“0” is read.
It stops after reset. Setting the bit is required.
Note : When using the internal oscillator,please do not use PLL.
R/W
WUODR12
WUODR0
WUODR4
R/W
14
22
30
6
0
0
0
0
-
Write “0011”
TMPM380/M382 - 4 / 24 -
R/W
WUODR11
WUODR3
R/W
R/W
13
21
29
5
1
0
0
0
-
-
Write “0”
WUODR10
WUODR2
R/W
R/W
12
20
28
4
1
0
0
0
-
-
R/W
Clock source
for Warm-up
timer(WUP)
0:
High-speed
oscillator
(follow to
WUPSEL2)
1:
Low-speed
oscillator
Clock source
for Warm-up
timer(WUP)
0: Internal
(OSC2)
1: External
(OSC1)
WUPSEL1
WUPSEL2
WUODR9
R/W
R/W
19
27
11
R
3
0
0
0
0
-
“0” is read.
PLL
operation
0: Stop
1: Oscillation
Port M or
X1/X2
0: PORT M
1: X1/X2
HOSCON
WUODR8
PLLON
R/W
R/W
10
18
26
R
2
0
0
0
0
-
Status of
Warm-up
timer (WUP)
0: warm-up
completed
1: Warm-up in
operation
Low-speed
oscillator
(External)
0: Stop
1: Oscillation
Selection of
high-speed
oscillator
0: Internal
(OSC2)
1: External
(OSC1)
WUODR7
OSCSEL
WUEF
XTEN
R/W
R/W
17
25
R
1
0
9
0
0
0
TMPM380/M382
Operation of
warm-up
timer (WUP)
0: don’t care
1: starting
warm-up
High-speed
oscillator 1
(External)
0: Stop
1: Oscillation
High-speed
oscillator 2
(Internal)
0: Stop
1: Oscillation
WUODR6
WUEON
XEN1
XEN2
R/W
R/W
16
24
W
0
0
8
0
1
0