TMP92xy26AXBG Toshiba, TMP92xy26AXBG Datasheet - Page 408

• Manufacturer Part Number: TMP92xy26AXBG
• Manufacturer: Toshiba

Specifications of TMP92xy26AXBG

• Package: FPGA228
• Rom Types(m=mask,p=otp, F=flash,e=eeprom): Romless
• Rom Combinations: Romless
• Ram Combinations: 144/288
• Architecture: 32-bit CISC
• Usb/spi Channels: 1/1
• Uart/sio Channels: 2
• I2c/sio Bus Channels: 1
• (s)dram Controller: 1
• Adc 10-bit Channel: 6
• Da Converter: -
• Timer 8-bit Channel: 8
• Timer 16-bit Channel: 2
• Pwm 8-bit Channels: -
• Pwm 16-bit Channels: -
• Cs/wait Controller: 4
• Dual Clock: Y
• Number Of I/o Ports: 136
• Power Supply Voltage(v): 3.0 to 3.6

EP1_MODE
(0789H)
EP2_MODE
(078AH)
EP3_MODE
(078BH)
bit Symbol
Read/Write
Reset State
bit Symbol
Read/Write
Reset State
bit Symbol
Read/Write
Reset State
3.16.3.24 EPx_MODE Register (x: 1 to 3)
Note1: When writing to this register, a recovery time of 5clocks at 12MHz is needed. After writing this register, insert
Note2: When writing to this register, endpoint is initialized same as RESET of COMMAND register.
Note1: Max packet size of Isochronous transfer type is 1023 bytes.
Note2: If wMaxPacketSize of descriptor has been set to other than 8, 16, ..., 1023, Payload more than descriptor
dummy instruction of 420 ns or longer.
value is set by auto-answer of Set_Configration and Set_Interface.
control must use appointed config or interface. Access this register to set mode.
control, after INT_SETUP interrupt is received, finish writing before accessing EOP
register. This register prohibits writing when it is other timing, and it is ignored.
This register sets transfer mode of endpoint (EP1 to EP3).
If SET_CONFIG and SET_INTERFACE processing is set to software control, this
There is a limitation to the timing that can be written.
If transaction for SET_CONFIG and SET_INTERFACE processing is set to software
DIRECTION (Bit0)
MODE [1:0] (Bit2 and bit1)
PAYLOAD [2:0] (Bit3, bit4 and bit5)
Others (Bit6 and bit7) Reserved
7
7
7
0: OUT
1: IN
00: Control transfer type
01: Isochronous transfer type
10: Bulk transfer type or interrupt transfer type
11: Interrupt (No toggle)
000:
001:
010:
011:
0100:128 bytes
0101:256 bytes
0110:512 bytes
0111:1023 bytes (Note1, 2)
16 bytes
32 bytes
64 bytes
8 bytes
6
6
6
Direction from host to device
Direction from device to host
Payload[2]
Payload[2]
Payload[2]
92CF26A-406
R/W
R/W
R/W
5
5
5
0
0
0
Payload[1]
Payload[1]
Payload[1]
R/W
R/W
R/W
4
4
4
0
0
0
Payload[0]
Payload[0]
Payload[0]
R/W
R/W
R/W
3
3
3
0
0
0
Mode[1]
Mode[1]
Mode[1]
R/W
R/W
R/W
2
2
2
0
0
0
Mode[0]
Mode[0]
Mode[0]
R/W
R/W
R/W
1
1
1
0
0
0
TMP92CF26A
2009-06-25
Direction
Direction
Direction
R/W
R/W
R/W
0
0
0
0
0
0