BU9253FS ROHM Co. Ltd., BU9253FS Datasheet
BU9253FS
Available stocks
Related parts for BU9253FS
BU9253FS Summary of contents
Page 1
... Radio cassette recorder, mini-component and karaoke systems. ●Product lineup Parameter Supply voltage Oscillation frequency Current consumption Operating temperature range Package Digital delay Echo level = 375kHz) CLK BU9253AS BU9253FS 4.0V～5.5V 4.0V～5.5V 375kHz 375kHz 6mA 6mA -10～+70℃ -10～+70℃ SDIP18 SSOP-A16 Fixed Fixed ...
Page 2
... Parameter Supply voltage Terminal voltage Power dissipation Storage temperature * Reduce by 6.0 mW/°C over 25°C ＜BU9253FS＞ Parameter Supply voltage Terminal voltage Power dissipation Storage temperature * Reduce by 5.0 mW/°C over 25°C ＜BU9262AFS＞ Parameter Supply voltage ...
Page 3
V =5.0V, f =375kHz Parameter Symbol Circuit Current I CC Voltage Gain 1 G Voltage Gain 2 G Output distortion 1 THD1 Output distortion 2 THD2 Output noise V NO1 voltage 1 Output ...
Page 4
200mVrms Parameter Symbol Circuit current I CC [Digital delay] Input/Output Gain AV1 THD1 THD2 Output distortion THD3 THD4 VNO1 VNO2 Output noise voltage VNO3 VNO4 Maximum output voltage ...
Page 5
Ta=25℃ 7.0 6.5 6.0 5.5 5.0 4.5 4.0 4.0 4.5 5.0 INPUT VOLTAGE : VCC [V] Fig.1 Current consumption V =5V / Ta=25℃ CC 4.5 4.0 3.5 Mute 3.0 2.5 2.0 1.5 1.0 Mute & OSC stop ...
Page 6
Ta=25℃ 4.5 4.7 4.9 5.1 5.3 INPUT VOLTAGE : VCC [V] Fig.13 Circuit current V =5V / Ta=25℃ -10 -20 -30 -40 -50 -60 -70 -80 -80 -60 -40 -20 AMPLITUDE ...
Page 7
... CR MUTE VCC ADINT IN ADINT OUT ADLPF OUT ADLPF GND ECHO VR BIAS DAINT IN DAINT OUT DALPF IN DALPF OUT Fig.26 BU9253FS pin assignment R7 20k C5 0.012u R4 R5 10k 20k R6 8. 4700p - + A/D side LPF operation amplifier A/D 側 ...
Page 8
Block diagram, Application circuit ＜BU9262AFS＞ ・Description of terminal No. Symbol 1 NC Not connected 2 TESTB Test negative logic input pin (normally “H” input) 3 SCK Serial clock input 4 SLT Serial latch input 5 SI Serial data ...
Page 9
Clock is generated by connecting external RC circuit. Clock is used for the delay counter. ・Mute control circuit (MUTE) By input voltage of the mute terminal, 3 statuses, that is, mute, mute release (operating), and ...
Page 10
This circuit controls delay time. -8 delay time can be selected by register ...
Page 11
Output/ input LPF circuit This is the LPF circuit connected to the ADC input unit and the DAC output unit. Delay time setting can be select by internal resistor. 48.0msec or below 96.0msec or below S1 S2 ・Auto mute ...
Page 12
... As an example, when clock frequency is 375kHz, then sample frequency is 375kHz ÷ 62.5kHz. Therefore, the delay time is: Delay time = (1 ÷ 62500) x 8192 = 131ms Clock frequency is determined by R2, C1 connected to CR terminal (pin 18 in BU9253AS, pin 16 in BU9253FS). When C, R are changed, oscillation frequency changes, but the delay time is kept fixed. ・ ...
Page 13
LPF and echo system gain When the ratio of original signal and echo is changed, R5, R6, R9, R11 are also changed, and the characteristics of LPF change too. Therefore necessary to change all the constants of ...
Page 14
Use 1) Absolute maximum ratings An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break down the devices, thus making impossible to identify breaking mode, such as a short ...
Page 15
Part Number BU9253 Part Number BU9262A SDIP18 <Dimension> 19.4 ± 0 0° ∼ 15° 0.5 ± 0.1 1.778 SSOP-A16 <Dimension> 6.6±0 0.15±0.1 ...
Page 16
Catalog No.05T411Be '06.4 ROHM C 1000 TSU ...
Page 17
Appendix No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product ...