TA8132AFG TOSHIBA Semiconductor CORPORATION, TA8132AFG Datasheet
TA8132AFG
Available stocks
Related parts for TA8132AFG
TA8132AFG Summary of contents
Page 1
... For adopting ceramic discriminator and ceramic resonator not necessary to adjust the FM quad detector circuit and FM ST DET VCO circuit. • S curve characteristics of FM detection output in TA8132ANG, TA8132AFG and TA2012NG, TA2012FG are reverse to each other. TA8132ANG, TA8132AFG: Reverse characteristic. TA2012NG, TA2012FG: Normal characteristic. ...
Page 2
Block Diagram (Note) We recommend Ceramic resonator: CSB456F18 Ceramic discriminator: CDA10.7MG18 (MURATA MFG CO., LTD) TA8132ANG/AFG,TA2012NG/FG 2 2004-10-12 ...
Page 3
Explanation Of Terminals Pin Item No ・IF count output sensitivity adjust terminal 2 ・FM IF divider control terminal 3 AM OSC 4 AM OSC OUT LOW CUT TA8132ANG/AFG,TA2012NG/FG Internal Circuit ― ...
Page 4
Pin Item No. 7 AGC 8 IF OUT OUT 10 TUN LED (tuning LED LED (stereo LED) 12 GND 13 R−OUT 14 L−OUT TA8132ANG/AFG,TA2012NG/FG Internal Circuit ― Voltage (V) (at no Signal) AM ...
Page 5
Pin Item No. 15 VCO LPF2 ・LPF terminal for synchronous detector 16 ・Bias terminal for switch circuit → open→FM 16 LPF1 ・LPF Terminal for phase detector 17 ・VCO stop terminal ...
Page 6
Pin Item No. 20 QUAD (FM QUAD. Detector BY−PASS 22 By−pass for AM/FM IF AMP 23 AM MIX OUT TA8132ANG/AFG,TA2012NG/FG Internal Circuit 6 DC Voltage (V) (at no Signal 2.4 ...
Page 7
Application Note 1. How to control the IF count output signal (pin(9) output) • Whether or not there is the IF count output signal (pin(9) output) is determined by the and of the pin(8) control voltage: V and tuning LED ...
Page 8
The gain loss AMP 0Ω IF −20dB (10.7MHz −20dB (1.3375MHz) (Note) ・In the condition of the mode possible to set ∞ (OPEN). 2 ...
Page 9
AM local oscillator buffer output • The output impedance of AM local oscillator buffer output pin (pin(4)) is 750Ω (typ.) (cf.P.3) • possible to reduce the output level to add the resistance between the pin(4) and V ...
Page 10
... Characteristic Supply voltage LED current LED voltage TA8132ANG Power dissipation TA8132AFG Operating Temperature Storage temperature (Note): Derated above 25°C in the proportion of 9.6mW / °C for TA8132ANG, TA2012NG and of 3.2mW / °C for TA8132AFG, TA2012FG. TA8132ANG/AFG,TA2012NG/ and for th CC 3V) CC Symbol Rating ...
Page 11
Electrical characteristics Unless Otherwise Specified 25° IF 10.7MHz, ∆f = ±22.5kHz 1MHz, MOD = 30%, f MPX: f Characteristic Symbol I (FM) CC Supply current I (AM) CC Input limiting ...
Page 12
Characteristic Symbol Gain Ｇ V Recovered output V OD voltage Signal to noise ratio Total harmonic THD distortion LED on sensitivity V L Local OSC buff. V (AM) OSC AM output voltage IF count output V (AM) ...
Page 13
Characteristic Symbol Input resistance R IN Output resistance R OUT Max. composite V in MAX signal input voltage (stereo) Separation Sep THD Monaural (monaural) Total harmonic THD distortion Stereo (stereo) Voltage gain G (MPX) V Channel balance ...
Page 14
Test Circuit 1 Coil Data (test circuit 1) Coil No. f (µ OSC 796kHz 288 IFT 455KHz 2 (S): SUMIDA ELECTRIC Co., Ltd. TA8132ANG/AFG,TA2012NG/FG Turn (pF) 1−2 2−3 1−3 4−6 ...
Page 15
Test Circuit 2 Coil Data (test circuit 2) Coil No. f (µ OSC 7.96MHz 1.4 (T): TOKO Co., Ltd. TA8132ANG/AFG,TA2012NG/ Turn (pF) 1−2 2−3 1−3 4−6 ― ― 15 ...
Page 16
TA8132ANG/AFG,TA2012NG/FG 16 2004-10-12 ...
Page 17
TA8132ANG/AFG,TA2012NG/FG 17 2004-10-12 ...
Page 18
TA8132ANG/AFG,TA2012NG/FG 18 2004-10-12 ...
Page 19
Package Dimensions Weight: 1.2g (typ.) TA8132ANG/AFG,TA2012NG/FG 19 2004-10-12 ...
Page 20
Package Dimensions Weight: 0.31g (typ.) TA8132ANG/AFG,TA2012NG/FG 20 2004-10-12 ...
Page 21
About solderability, following conditions were confirmed • Solderability (1) Use of Sn-63Pb solder Bath · solder bath temperature = 230°C · dipping time = 5 seconds · the number of times = once · use of R-type flux (2) Use ...