MAX1035 Maxim Integrated Products, MAX1035 Datasheet - Page 14

• Manufacturer Part Number: MAX1035
• Description: (MAX1034 / MAX1035) Serial 14-Bit ADCs
• Manufacturer: Maxim Integrated Products

The MAX1034 has eight single-ended analog input
channels or four differential channels (see the Block
Diagram at the end of the data sheet). The MAX1035
has four single-ended analog input channels or two dif-
ferential channels. Each analog input channel is inde-
pendently software programmable for seven
single-ended
-V
and ±V
±V
channels are fault tolerant to ±6V. A fault condition on
an idle channel does not affect the conversion result of
other channels.
To maintain a low-noise environment, the MAX1034 and
MAX1035 provide separate power supplies for each
section of circuitry. Table 1 shows the four separate
power supplies. Achieve optimal performance using
separate AV
Alternatively, connect AV
together as close to the device as possible for a conve-
nient power connection. Connect AGND1, AGND2,
8-/4-Channel, ±V
Serial 14-Bit ADCs
Table 1. MAX1034/MAX1035 Power Supplies and Bypassing
Table 2. Analog Input Configuration Byte
14
NUMBER
REF
REF
SUPPLY/GROUND
BIT
______________________________________________________________________________________
DV
7
6
5
4
3
2
1
0
/2 to 0, 0 to +V
AV
AV
, and ±2 x V
DV
REF
DDO
DD2
DD1
POWER
DD
) and three differential input ranges (±V
/DGNDO
/AGND2
/AGND1
/DGND
DD1
DIF/SGL
START
NAME
C2
C1
C0
R2
R1
R0
, AV
input
REF
REF
DD2
). Additionally, all analog input
Start Bit. The first logic 1 after CS goes low defines the beginning of the analog input configuration byte.
Channel-Select Bits. SEL[2:0] select the analog input channel to be configured (Tables 4 and 5).
Differential or Single-Ended Configuration Bit. DIF/SGL = 0 configures the selected analog input channel
for single-ended operation. DIF/SGL = 1 configures the channel for differential operation. In single-ended
mode, input voltages are measured between the selected input channel and AGND1, as shown in
Table 4. In differential mode, the input voltages are measured between two input channels, as shown in
Table 5. Be aware that changing DIF/SGL adjusts the FSR, as shown in Table 6.
Input-Range-Select Bits. R[2:0] select the input voltage range, as shown in Table 6 and Figure 7.
, -V
, DV
ranges
SUPPLY VOLTAGE
REF
DD1
DD
RANGE (V)
4.75 to 5.25
4.75 to 5.25
4.75 to 5.25
2.7 to 5.25
to 0, ±V
, and DV
, AV
Power Supplies
(0
DD2
REF
REF
to
DDO
, and DV
/4, ±V
+V
supplies.
REF
Multirange Inputs,
REF
REF
TYPICAL SUPPLY
CURRENT (mA)
/2,
DD
/2,
/2,
17.5
0.2
3.0
0.9
AGND3, DGND, and DGNDO together as close to the
device as possible. Bypass each supply to the corre-
sponding ground using a 0.1µF capacitor (Table 1). If
significant low-frequency noise is present, add a 10µF
capacitor in parallel with the 0.1µF bypass capacitor.
The MAX1034/MAX1035 ADCs feature a fully differen-
tial, successive-approximation register (SAR) conver-
sion technique and an on-chip T/H block to convert
voltage signals into a 14-bit digital result. Both single-
ended and differential configurations are supported
with programmable unipolar and bipolar signal ranges.
The MAX1034/MAX1035 feature a switched-capacitor
T/H architecture that allows the analog input signal to be
stored as charge on sampling capacitors. See Figures 2,
3, and 4 for T/H timing and the sampling instants for
each operating mode. The MAX1034/MAX1035 analog
input circuitry buffers the input signal from the sampling
capacitors, resulting in a constant analog input current
with varying input voltage (Figure 5).
DESCRIPTION
Digital I/O
Analog Circuitry
Analog Circuitry
Digital Control Logic and
Memory
CIRCUIT SECTION
Track-and-Hold Circuitry
Converter Operation
0.1µF to DGNDO
0.1µF to AGND2
0.1µF to AGND1
0.1µF to DGND
BYPASSING