MAX11645 Maxim Integrated Products, MAX11645 Datasheet - Page 17
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX11645
Manufacturer Part Number
MAX11645
Description
2-Wire Serial 12-Bit ADCs
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX11645.pdf
(21 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX11645EUA+T
Manufacturer:
MAXIM
Quantity:
37
Table 6. Reference Voltage and REF Format
X = Don’t care.
*Preferred configuration for internal reference.
The configuration and setup registers (Tables 1 and 2)
default to a single-ended, unipolar, single-channel con-
version on AIN0 using the internal clock with V
reference. The memory contents are unknown after
power-up.
Automatic shutdown occurs between conversions when
the MAX11644/MAX11645 are idle. All analog circuits
participate in automatic shutdown except the internal
reference due to its prohibitively long wake-up time.
When operating in external clock mode, a STOP, not-
acknowledge, or repeated START condition must be
issued to place the devices in idle mode and benefit
from automatic shutdown. A STOP condition is not nec-
essary in internal clock mode to benefit from automatic
shutdown because power-down occurs once all con-
version results are written to memory (Figure 10). When
using an external reference or V
analog circuitry is inactive in shutdown and supply cur-
rent is less than 0.5µA. The digital conversion results
obtained in internal clock mode are maintained in mem-
ory during shutdown and are available for access
through the serial interface at any time prior to a STOP
or a repeated START condition.
When idle, the MAX11644/MAX11645 continuously wait
for a START condition followed by their slave address
(see the Slave Address section). Upon reading a valid
address byte, the MAX11644/MAX11645 power up. The
internal reference requires 10ms to wake up, so when
using the internal reference it should be powered up
10ms prior to conversion or powered continuously.
Wake-up is invisible when using an external reference
or V
SEL2
DD
0
0
1
1
1
1
as the reference.
2.7V to 3.6V and 4.5V to 5.5V, Low-Power,
Applications Information
SEL1
______________________________________________________________________________________
0
1
0
0
1
1
1-/2-Channel, 2-Wire Serial, 12-Bit ADCs
SEL0
X
X
0
1
0
1
Automatic Shutdown
DD
Power-On Reset
as a reference, all
External reference
Internal reference
Internal reference
Internal reference
Internal reference
DD
REFERENCE
VOLTAGE
as the
V
DD
Automatic shutdown results in dramatic power savings,
particularly at slow conversion rates and with internal
clock. For example, at a conversion rate of 10ksps, the
average supply current for the MAX11645 is 60µA (typ)
and drops to 6µA (typ) at 1ksps. At 0.1ksps the aver-
age supply current is just 1µA, or a minuscule 3µW of
power consumption. See Average Supply Current vs.
Conversion Rate (External Clock) in the Typical
Operating Characteristics section).
SEL[2:0] of the setup byte (Table 1) control the refer-
ence configuration (Table 6).
The internal reference is 4.096V for the MAX11644 and
2.048V for the MAX11645. When REF is configured to
be an internal reference output (SEL[2:1] = 11), decou-
ple REF to GND with a 0.1µF capacitor and a 2kΩ
series resistor (see the Typical Operating Circuit ). Once
powered up, the reference always remains on until
reconfigured. The internal reference requires 10ms to
wake up and is accessed using SEL0 (Table 6). When
in shutdown, the internal reference output is in a high-
impedance state. The reference should not be used to
supply current for external circuitry. The internal refer-
ence does not require an external bypass capacitor
and works best when left unconnected (SEL1 = 0).
The external reference can range from 1V to V
maximum conversion accuracy, the reference must be
able to deliver up to 40µA and have an output imped-
ance of 500kΩ or less. If the reference has a higher
output impedance or is noisy, bypass it to GND as
close as possible to REF with a 0.1µF capacitor.
Reference output
Reference output
Reference input
Not connected*
Not connected*
Not connected
REF
INTERNAL REFERENCE
Reference Voltage
External Reference
Internal Reference
www.DataSheet4U.com
Always off
Always off
Always off
Always on
Always off
Always on
STATE
DD
. For
17