MAX1718 Maxim, MAX1718 Datasheet - Page 12

• Manufacturer Part Number: MAX1718
• Description: Notebook CPU Step-Down Controller for Intel Mobile Voltage Positioning IMVP-II
• Manufacturer: Maxim

Table 1. Component Suppliers
Notebook CPU Step-Down Controller for Intel
Mobile Voltage Positioning (IMVP - II)
The MAX1718 requires an external 5V bias supply in
addition to the battery. Typically, this 5V bias supply is
the notebook’s 95% efficient 5V system supply.
Keeping the bias supply external to the IC improves
efficiency and eliminates the cost associated with the
5V linear regulator that would otherwise be needed to
supply the PWM circuit and gate drivers. If stand-alone
capability is needed, the 5V supply can be generated
with an external linear regulator.
The 5V bias supply must provide V
and V
drawn is:
where I
and Q
gate-charge specification limits at V
V+ and V
source is a fixed 4.5V to 5.5V supply. If the 5V bias
supply is powered up prior to the battery supply, the
enable signal (SKP/SDN going from low to high or
open) must be delayed until the battery voltage is pre-
sent to ensure startup.
12
Central Semiconductor
Dale-Vishay
Fairchild
International Rectifier
Kemet
Motorola
Nihon
Panasonic
Taiyo Yuden
TDK
Toko
Sanyo
SGS-Thomson
Sumida
Zetex
I
MANUFACTURER
BIAS
______________________________________________________________________________________
DD
G1
CC
= I
(gate-drive power), so the maximum current
DD
and Q
CC
is 800µA (typ), f is the switching frequency,
can be tied together if the input power
+ f (Q
5V Bias Supply (V
G2
G1
are the MOSFET data sheet total
Detailed Description
+ Q
516-435-1110
402-564-3131
408-721-2181
310-322-3331
408-986-0424
602-303-5454
847-843-7500
714-373-7939
408-573-4150
847-390-4373
800-745-8656
619-661-6835
617-259-0300
708-956-0666
516-543-7100
USA PHONE
G2
) = 10mA to 40mA (typ)
CC
GS
(PWM controller)
= 5V.
CC
FACTORY FAX
516-435-1824
402-563-6418
408-721-1635
310-322-3332
408-986-1442
602-994-6430
847-843-2798
714-373-7183
408-573-4159
847-390-4428
408-943-9790
619-661-1055
617-259-9442
708-956-0702
516-864-7630
and V
DD
)
The Quick-PWM control architecture is a pseudofixed-
frequency, constant-on-time current-mode type with
voltage feed-forward (Figure 2). This architecture relies
on the output filter capacitor’s ESR to act as the cur-
rent-sense resistor, so the output ripple voltage pro-
vides the PWM ramp signal. The control algorithm is
simple: the high-side switch on-time is determined sole-
ly by a one-shot whose period is inversely proportional
to input voltage and directly proportional to output volt-
age. Another one-shot sets a minimum off-time (400ns
typ). The on-time one-shot is triggered if the error com-
parator is low, the low-side switch current is below the
current-limit threshold, and the minimum off-time one-
shot has timed out.
The heart of the PWM core is the one-shot that sets the
high-side switch on-time. This fast, low-jitter, adjustable
one-shot includes circuitry that varies the on-time in
response to battery and output voltage. The high-side
switch on-time is inversely proportional to the battery
voltage as measured by the V+ input, and proportional
to the output voltage. This algorithm results in a nearly
constant switching frequency despite the lack of a
fixed-frequency clock generator. The benefits of a con-
stant switching frequency are twofold: first, the frequency
can be selected to avoid noise-sensitive regions such
as the 455kHz IF band; second, the inductor ripple-cur-
rent operating point remains relatively constant, resulting
in easy design methodology and predictable output
voltage ripple.
where K is set by the TON pin-strap connection and
0.075V is an approximation to accommodate the expect-
ed drop across the low-side MOSFET switch (Table 2).
The on-time one-shot has good accuracy at the operating
points specified in the Electrical Characteristics table
(±10% at 200kHz and 300kHz, ±12% at 550kHz and
1000kHz). On-times at operating points far removed from
the conditions specified in the Electrical Characteristics
table can vary over a wider range. For example, the
1000kHz setting will typically run about 10% slower with
inputs much greater than +5V due to the very short on-
times required.
On-times translate only roughly to switching frequencies.
The on-times guaranteed in the Electrical Character-
istics table are influenced by switching delays in the
Free-Running, Constant On-Time PWM
Controller with Input Feed-Forward
On-Time = K (V
On-Time One-Shot (TON)
OUT
+ 0.075V) / V
IN