MAX8686 Maxim Integrated Products, MAX8686 Datasheet - Page 22
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX8686
Manufacturer Part Number
MAX8686
Description
DC-DC Converter Delivers Up To 25A Per Phase
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX8686.pdf
(22 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX8686ETL+T
Manufacturer:
MAIXM
Quantity:
3 636
www.DataSheet4U.com
Single/Multiphase, Step-Down,
DC-DC Converter Delivers Up to 25A Per Phase
Careful PCB layout is critical to achieve low switching
losses and clean, stable operation. The switching
power stage requires particular attention. Follow these
guidelines for good PCB layout:
1)
2)
3)
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
22 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2008 Maxim Integrated Products
PHASE/REFO
TOP VIEW
Place IC decoupling capacitors as close to the IC
pins as possible. Separate the power and analog
ground planes. Place the input ceramic decoupling
capacitor directly across and as close as possible
to IN and PGND. This is to help contain the high
switching current within this small loop.
For output current greater than 10A, a four-layer
PCB is recommended. Pour an analog ground
plane in the second layer underneath the IC to min-
imize noise coupling.
Connect input and output capacitor to the PGND
plane and the VL capacitor to RTN. Connect all
analog signals to GND. The frequency-setting
capacitor should be connected to GFREQ.
COMP
REFIN
FREQ
ILIM
POK
BST
RS+
RS-
SS
31
32
33
34
35
36
37
38
39
40
+
30
1
Applications Information
GND_EP
29
2
28
3
27
4
MAX8686
PCB Layout Guidelines
TQFN
26
5
Pin Configuration
25
6
IN_EP
LX_EP
24 23 22
7
8
9
10
21
20 IN
19
18
17
16
15
14
13
12
11
IN
IN
N.C.
LX
PGND
PGND
PGND
PGND
PGND
4)
5)
6)
7)
8)
9)
10) Refer to the MAX8686 Evaluation Kit for an exam-
For the latest package outline information, go to
www.maxim-ic.com/packages.
PROCESS: BiCMOS
PACKAGE TYPE
is a registered trademark of Maxim Integrated Products, Inc.
Connect PGND, GND, and RTN at the return path
of the input bypass capacitor.
Signals shared by the master and slave (ILIM,
COMP, and FREQ) should not run close to switch-
ing signals.
Place the inductor current-sense resistor and
capacitor as close to the inductor as possible.
Make a Kelvin connection to minimize the effect of
PCB trace resistance.
Connect the exposed pad sections to the corre-
sponding IC pins and allow sufficient copper area
to help cooling the device.
Place the REFIN and compensation components
as close to the IC pins as possible.
Connect remote-sense input RS+ and RS- directly
to the load voltage regulation point and use Kelvin
connection for the two traces.
ple layout.
40 TQFN
40 TQFN
PACKAGE CODE
Package Information
T4066MN-1
T4066M-1
Chip Information
DOCUMENT NO.
21-0177
21-0177