CTL0510-0N5-B Cyntec Co., Ltd., CTL0510-0N5-B Datasheet
CTL0510-0N5-B
Related parts for CTL0510-0N5-B
CTL0510-0N5-B Summary of contents
Page 1
... SERIES THIN FILM CHIP INDUCTOR 1. Scope This specification applies to 0.5mm x 1.0mm (0402) size, fixed thin film chip inductor rectangular type. 2. Type Designation CTL0510 - ＊＊＊ - ＊ (1) (2) Where (1) Product identification code (2) Nominal inductance value : For example –- 3N9 : 3 ...
Page 2
... CTL0510-1N0 1.0 CTL0510-1N2 1.2 CTL0510-1N5 1.5 CTL0510-1N6 1.6 CTL0510-1N8 1.8 CTL0510-2N0 2.0 CTL0510-2N2 2.2 CTL0510-2N4 2.4 CTL0510-2N5 2.5 CTL0510-2N7 2.7 CTL0510-3N0 3 CTL0510-3N1 3 0.3 nH CTL0510-3N2 3.2 CTL0510-3N3 3.3 CTL0510-3N5 3.5 CTL0510-3N6 3.6 CTL0510-3N9 3.9 CTL0510-4N4 4.4 CTL0510-4N7 4.7 CTL0510-5N0 5.0 CTL0510-5N6 5.6 CTL0510-6N0 6.0 CTL0510-6N8 6 CTL0510-7N1 7 CTL0510-8N2 8 CTL0510-8N5 8.5 Q (Typical) @Frequency(MHz) Measuring Frequency 100 300 800 (MHz) 100 ...
Page 3
... CTL0510-10N 10 CTL0510-12N 12 CTL0510-15N 15 CTL0510-18N 18 CTL0510-22N 22 CTL0510-27N 27 CTL0510-33N 33 ±10% CTL0510-39N 39 ※Measurement Instrument: L,Q : Agilent 4287A LCR METER + 16196B TEST FIXTURE. SRF : Agilent 8510 VECTOR NETWORK ANALYZER (Typical value ). Rdc : Agilent DIGITAL MILLIOHM METER HP4338A or equivalent. ...
Page 4
... CYNTEC CO., LTD. 乾坤科技股份有限公司 4-2 Operating Temperature Range 4-2-1 Operating Temperature Range 125℃ 4-2-2 Storage Temperature Range 125℃ 5. Characteristics 5-1 Electrical Unless otherwise specified, measurements shall be performed under the condition below. a. Temperature : 24 ± 2℃ ...
Page 5
... CYNTEC CO., LTD. 乾坤科技股份有限公司 5-1-5 Temperature Coefficient Temperature Coefficient of Inductance shall be within 0 to +125 ppm/℃. Temperature Coefficient of Q value shall be -0.25% /℃ or less. Temperature Coefficient of DC Resistance shall be +0.45% /℃ or less. Measurement shall be performed at RT and RT+100℃, and the calculation shall be performed with the measured values ...
Page 6
... CYNTEC CO., LTD. 乾坤科技股份有限公司 5-1-9 Voltage Proof No mechanical damage shall be observed. Electrical characteristics shall be within specification. The inductor shall be tested as shown in paragraph 5-1-7. Test Voltage : 100V 5-2 Mechanical 5-2-1 Bending Test No mechanical damage shall be observed. Electrical characteristics shall be within specification. ...
Page 7
... CYNTEC CO., LTD. 乾坤科技股份有限公司 5-2-3 Resistance to Soldering Heat No mechanical damage shall be observed. Electrical characteristics shall be within specification. (1) Solder bath method Pre-heat : 100 to 110℃ Temperature : 270 ± 5℃ (2) Reflow soldering method Peak temperature : 240 ± 5℃ max. 5 seconds ...
Page 8
... CYNTEC CO., LTD. 乾坤科技股份有限公司 5-3-2 Dump Heat with Load No mechanical damage shall be observed. Electrical characteristics shall be within specification. 40 ± 2℃ with relative humidity 95%. DC rated voltage for 1.5 hours on 0.5 hours off 1,000 +48/-0 hours. 5-3-3 Endurance at 70℃ Resistance to Soldering Heat No mechanical damage shall be observed ...
Page 9
... CYNTEC CO., LTD. 乾坤科技股份有限公司 6. Packaging 6-1 Dimensions 6-1-1 Tape Packaging Dimensions 0.42± 0.05 Inductor A 0.48± 0.1 Material : Paper 6-1-2 Reel Dimensions +0.1 Ø1.5 −0.0 4.0± 0.1 B Carrier cavity A = 1.13± 0. 0.63± 0.05 Direction marking 3 3 ¡ 1 DOCUMENT : LLD00000 REVISION : A2 PAGE : Sprocket hole 1.75± ...
Page 10
... CYNTEC CO., LTD. 乾坤科技股份有限公司 6-2 Peel Strength of Top Cover Tape Pull out The peel speed shall be about 300 mm/minute The peel strength of top cover tape shall be between 0.1 to 0.7N. 6-3 Quantity per Reel 10,000 pieces / reel 6-4 Marking The following items shall be marked on the reel ...
Page 11
... CYNTEC CO., LTD. 乾坤科技股份有限公司 7. Caution on using chip inductor 7-1 When storing the product (1) Store the product in an environmentally well-controlled room (temperature: 5-35℃, humidity : 45-85% RH). Humidity should be kept as low as possible. (2) Store the product in a place free of substances which deteriorate Solderability (moisture, dust) and which is free of poisonous gases (hydrogen chloride, hydrogen sulfide) ...
Page 12
... CYNTEC CO., LTD. 乾坤科技股份有限公司 7-3 When storing the product (1) Warps of the mounted board will causes mechanical stress on the products. Be sure to handle the mounted board carefully so as not to bend. Product edge, protective coating or housing surface of the product should be free from excess mechanical stress ...