ACS8525T Semtech, ACS8525T Datasheet - Page 43
ACS8525T
Manufacturer Part Number
ACS8525T
Description
Line Card Protection Switch for SONET/SDH Systems
Manufacturer
Semtech
Datasheet
1.ACS8525T.pdf
(112 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ACS8525T
Manufacturer:
SEMTECH/美国升特
Quantity:
20 000
- Current page: 43 of 112
- Download datasheet (915Kb)
Address (hex):
Revision 3.01/August 2005 © Semtech Corp.
ADVANCED COMMUNICATIONS
Register Name
phase_alarm
Address (hex):
Bit No.
Bit 7
7
6
5
4
3
2
1
0
03
test_register1
disable_180
Description
phase_alarm (phase alarm (R/O))
Instantaneous result from DPLL1.
disable_180
Normally the DPLL will try to lock to the nearest
edge (±180°) for the first 2 seconds when locking to
a new reference. If the DPLL does not determine
that it is phase locked after this time, then the
capture range reverts to ±360°, which corresponds
to frequency and phase locking. Forcing the DPLL
into frequency locking mode may reduce the time to
frequency lock to a new reference by up to two
seconds. However, this may cause an unnecessary
phase shift of up to 360° when the new and old
references are very close in frequency and phase.
Not used.
resync_analog (analog dividers re-synchronization)
The analog output dividers include a
synchronization mechanism to ensure phase lock at
low frequencies between the input and the output.
Set to 0
Test Control. Leave unchanged or set to 0.
8k Edge Polarity
When lock 8k mode is selected for the current input
SEC, this bit allows the system to lock on either the
rising or the falling edge of the input clock.
Set to 0
Test Control. Leave unchanged or set to 0.
Set to 0
Test Control. Leave unchanged or set to 0.
04
Bit 6
test_register2
Bit 5
Description
resync_analog
Do not use. Only zero should be written to this address.
Bit 4
FINAL
Page 43
(R/W) Register containing various
test controls (not normally used).
Set to 0
Bit Value
Bit 3
0
1
0
1
0
1
0
0
1
0
0
-
8k Edge Polarity Set to 0
Value Description
DPLL1 reporting phase locked.
DPLL1 reporting phase lost.
DPLL1 automatically determines frequency lock
enable.
DPLL1 forced to always frequency and phase lock.
-
Analog divider only synchronized during first 2
seconds after power-up.
Analog dividers always synchronized.This keeps the
clocks divided down from the APLL output, in sync
with equivalent frequency digital clocks in the DPLL.
Hence ensuring that 6.48 MHz output clocks, and
above, are in sync with the DPLL even though only a
77.76 MHz clock drives the APLL.
-
Lock to falling clock edge.
Lock to rising clock edge.
-
-
Bit 2
Default Value
ACS8525 LC/P
Bit 1
DATASHEET
www.semtech.com
0001 0100
Set to 0
Bit 0
Related parts for ACS8525T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Image Sensor, CMOS|CCD, 1026x1026 Pixels, 132pin LCC
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
Part Number:
Description:
High Performance Area CMOS Image Sensor
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
Part Number:
Description:
Image Sensor, CMOS, 2048x2048 Pixels, 144pin CPGA
Manufacturer:
Photon Vision Systems, Inc.
Datasheet:
Part Number:
Description:
SMD Mini Spring Coils
Manufacturer:
ECM [ECM Electronics Limited.]
Datasheet:
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
VOLTAGE SUPPRESSOR, TRANSIENT SEMTECH
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet: