LT1175I Linear Technology, LT1175I Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LT1175I
Manufacturer Part Number
LT1175I
Description
500mA Negative Low Dropout Micropower Regulator
Manufacturer
Linear Technology
Datasheet
1.LT1175I.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LT1175IN8-5
Manufacturer:
LT
Quantity:
14
Company:
Part Number:
LT1175IQ#PBF
Manufacturer:
LINEAR
Quantity:
3 000
Part Number:
LT1175IQ#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1175IQ-5#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LT1175IQ-5#TRPBF
Manufacturer:
Linear
Quantity:
2 000
Part Number:
LT1175IQ-5#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1175IS8
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1175IS8#PBF
Manufacturer:
LTNEAR
Quantity:
20 000
Company:
Part Number:
LT1175IS8#TR
Manufacturer:
LT
Quantity:
3 000
TYPICAL PERFORMANCE CHARACTERISTICS
SENSE Pin: The SENSE pin is used in the adjustable
version to allow custom selection of output voltage, with
an external divider set to generate 3.8V at the SENSE pin.
Input bias current is typically 75nA flowing out of the pin.
Maximum forced voltage on the SENSE pin is 2V and –10V
with respect to GND pin.
The fixed 5V version utilizes the SENSE pin to give true
Kelvin connections to the load or to drive an external pass
transistor for higher output currents. Bias current out of
the 5V SENSE pin is approximately 12 A. Separating the
SENSE and OUTPUT pins also allows for a new loop
compensation technique described in the Applications
Information section.
SHDN Pin: The SHDN pin is specially configured to allow
it to be driven from either positive voltage logic or with
negative only logic. Forcing the SHDN pin 2V either above
or below the GND pin will turn the regulator on. This makes
it simple to connect directly to positive logic signals for
active low shutdown. If no positive voltages are available,
the SHDN pin can be driven below the GND pin to turn the
regulator on. When left open, the SHDN pin will default low
to a regulator “on” condition . For all voltages below
absolute maximum ratings, the SHDN pin draws only a few
PIN
U
FUNCTIONS
U
20
16
12
8
4
0
GND pin Current
0
U
TRANSISTOR
IN DROPOUT
0.1
T
J
T
J
= –55 C
POWER
= 25 C
0.2
OUTPUT CURRENT (A)
W
0.3
V
U
IN
0.4
T
– V
J
= 25 C
OUT
V
T
IN
J
0.5
= 25 C
– V
2V
OUT
0.6
1175 G10
3V
0.7
microamperes of current (see Typical Performance Char-
acteristics). Maximum voltage on the SHDN pin is 15V,
– 20V with respect to the GND pin and 35V, – 5V with
respect to the negative input pin.
I
of the power transistor. When left open, they float several
hundred millivolts above the negative input voltage. When
shorted to the input voltage, they increase current limit by
a minimum of 200mA for I
pins must be connected only to the input voltage, either
directly or through a resistor.
OUTPUT Pin: The OUTPUT pin is the collector of the NPN
power transistor. It can be forced to the input voltage, to
ground or up to 2V positive with respect to ground without
damage or latchup (see Output Voltage Reversal in Appli-
cations Information section). The LT1175 has foldback
current limit, so maximum current at the OUTPUT pin is a
function of input-to-output voltage. See Typical Perfor-
mance Characteristics.
GND Pin: The GND pin has a quiescent current of 45 A at
zero load current, increasing by approximately 10 A per
mA of output current. At 500mA output current, GND pin
current is about 5mA. Current flows into the GND pin.
LIM
Pins: The two current limit pins are emitter sections
100
RIPPLE REJECTION IS RELATIVELY INDEPENDENT OF
INPUT VOLTAGE AND LOAD FOR CURRENTS BETWEEN
25mA AND 500mA. LARGER OUTPUT CAPACITORS DO
NOT IMPROVE REJECTION FOR FREQUENCIES BELOW
50kHz. AT VERY LIGHT LOADS, REJECTION WILL
IMPROVE WITH LARGER OUTPUT CAPACITORS
80
60
40
20
0
10
Ripple Rejection
I
V
C
(ADJUSTABLE)
OUT
IN
OUT
V
– V
= 100mA
OUT
= 1 F TANT
100
OUT
= 12V
= 2V
FREQUENCY (Hz)
1k
V
(ADJUSTABLE)
WITH 0.1 F ACROSS
DIVIDER RESISTOR
OUT
LIM2
= 12V
10k
and 400mA for I
V
(FIXED)
OUT
100k
= 5V
1M
1175 G11
LT1175
LIM4
. These
5