SC16C2550 Philips Semiconductors, SC16C2550 Datasheet - Page 20

no-image

SC16C2550

Manufacturer Part Number
SC16C2550
Description
Dual UART with 16 bytes of transmit and receive FIFOs and infrared (IrDA) encoder/decoder
Manufacturer
Philips Semiconductors
Datasheets

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
SC16C2550BIA44
Manufacturer:
EVERLIGHT
Quantity:
99
Part Number:
SC16C2550BIA44
Manufacturer:
NXP
Quantity:
3 224
Part Number:
SC16C2550BIA44
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
SC16C2550BIA44,512
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
SC16C2550BIA44,518
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
SC16C2550BIA44,529
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Part Number:
SC16C2550BIA44518
Manufacturer:
NXP Semiconductors
Quantity:
135
Part Number:
SC16C2550BIB48
Manufacturer:
NXP
Quantity:
8 000
Part Number:
SC16C2550BIB48
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Part Number:
SC16C2550BIB48128
Manufacturer:
NXP Semiconductors
Quantity:
1 889
Part Number:
SC16C2550BIB48151
Manufacturer:
NXP Semiconductors
Quantity:
135
Part Number:
SC16C2550BIBS,151
Manufacturer:
NXP
Quantity:
1 861
Part Number:
SC16C2550IN40
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Philips Semiconductors
9397 750 11621
Product data
7.3.2 FIFO mode
Table 9:
Bit
7-6
5-4
3
2
FIFO Control Register bits description
Symbol
FCR[7]
(MSB),
FCR[6]
(LSB)
FCR[5-4]
FCR[3]
FCR[2]
Dual UART with 16 bytes of transmit and receive FIFOs and IrDA
Rev. 03 — 19 June 2003
Description
RCVR trigger. These bits are used to set the trigger level for the
receive FIFO interrupt.
An interrupt is generated when the number of characters in the
FIFO equals the programmed trigger level. However, the FIFO will
continue to be loaded until it is full. Refer to
Not used; initialized to logic 0.
DMA mode select.
Transmit operation in mode ‘0’: When the SC16C2550 is in the
16C450 mode (FIFOs disabled; FCR[0] = logic 0) or in the FIFO
mode (FIFOs enabled; FCR[0] = logic 1; FCR[3] = logic 0), and
when there are no characters in the transmit FIFO or transmit
holding register, the TXRDY pin in PLCC44 or LQFP48 packages
will be a logic 0. Once active, the TXRDY pin will go to a logic 1
after the first character is loaded into the transmit holding register.
Receive operation in mode ‘0’: When the SC16C2550 is in
mode ‘0’ (FCR[0] = logic 0), or in the FIFO mode (FCR[3] = logic 0)
and there is at lease one character in the receive FIFO, the
RXRDY pin will be a logic 0. Once active, the RXRDY pin on
PLCC44 and LQFP48 packages will go to a logic 1 when there are
no more characters in the receiver.
Transmit operation in mode ‘1’: When the SC16C2550 is in
FIFO mode (FCR[0] = logic 1; FCR[3] = logic 1), the TXRDY pin on
PLCC44 and LQFP48 packages will be a logic 1 when the transmit
FIFO is completely full. It will be a logic 0 if one or more FIFO
locations are empty.
Receive operation in mode ‘1’: When the SC16C2550 is in FIFO
mode (FCR[0] = logic 1; FCR[3] = logic 1) and the trigger level has
been reached, or a Receive Time-Out has occurred, the RXRDY
pin on PLCC44 and LQFP48 packages will go to a logic 0. Once
activated, it will go to a logic 1 after there are no more characters in
the FIFO.
XMIT FIFO reset.
Logic 0 (or cleared) = normal default condition.
Logic 1 = RX trigger level.
Logic 0 = Set DMA mode ‘0’
Logic 1 = Set DMA mode ‘1’
Logic 0 = Transmit FIFO not reset (normal default condition).
Logic 1 = Clears the contents of the transmit FIFO and resets
the FIFO counter logic (the transmit shift register is not cleared
or altered). This bit will return to a logic 0 after clearing the FIFO.
© Koninklijke Philips Electronics N.V. 2003. All rights reserved.
SC16C2550
Table
encoder/decoder
10.
20 of 46

Related parts for SC16C2550