si4330 Silicon Laboratories, si4330 Datasheet - Page 46
![no-image](/images/no-image-200.jpg)
si4330
Manufacturer Part Number
si4330
Description
Si4330 Ism Receiver
Manufacturer
Silicon Laboratories
Datasheet
1.SI4330.pdf
(142 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
si4330-A0-FM
Manufacturer:
SILICON
Quantity:
740
Part Number:
si4330-A0-FM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Part Number:
si4330-B1-FM
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Company:
Part Number:
si4330-B1-FM-02T
Manufacturer:
SILICON
Quantity:
112
Company:
Part Number:
si4330-B1-FMR
Manufacturer:
HIROSE
Quantity:
3 200
Part Number:
si4330-B1-FMR
Manufacturer:
SILICON LABS/芯科
Quantity:
20 000
Part Number:
si4330BDY-T1-E3
Manufacturer:
VISHAY/威世
Quantity:
20 000
Part Number:
si4330BDY-T1-GE3
Manufacturer:
VISHAY/威世
Quantity:
20 000
Company:
Part Number:
si4330DY-T1-E3
Manufacturer:
VISHAY
Quantity:
464
Company:
Part Number:
si4330DY-T1-E3
Manufacturer:
VISHAY
Quantity:
30 000
Si4330
8.2. Microcontroller Clock
The crystal oscillator frequency is divided down internally and may be output to the microcontroller through GPIO2.
This feature is useful to lower BOM cost by using only one crystal in the system. The system clock frequency is
selectable from one of 8 options, as shown below. Except for the 32.768 kHz option, all other frequencies are
derived by dividing the Crystal Oscillator frequency. The 32.768 kHz clock signal is derived from an internal RC
Oscillator or an external 32 kHz Crystal, depending on which is selected. The GPIO2 default is the microcontroller
clock with a 1 MHz microcontroller clock output.
If the microcontroller clock option is being used there may be the need of a System Clock for the microcontroller
while the Si4330 is in SLEEP mode. Since the Crystal Oscillator is disabled in SLEEP mode in order to save
current, the low-power 32.768 kHz clock can be automatically switched to become the microcontroller clock. This
feature is called Enable Low Frequency Clock and is enabled by the enlfc bit. When enlfc = 1 and the chip is in
SLEEP mode then the 32.768 kHz clock will be provided to the microcontroller as the System Clock, regardless of
the setting of mclk[2:0]. For example, if mclk[2:0] = 000, 30 MHz will be provided through the GPIO output pin to
the microcontroller as the System Clock in all IDLE or RX states. When the chip is commanded to SLEEP mode,
the System Clock will become 32.768 kHz.
Another available feature for the microcontroller clock is the Clock Tail, clkt[1:0]. If the Enable Low Frequency
Clock feature is not enabled (enlfc = 0), then the System Clock to the microcontroller is disabled in SLEEP mode.
However, it may be useful to provide a few extra cycles for the microcontroller to complete its operation prior to the
shutdown of the System Clock signal. Setting the clkt[1:0] field will provide additional cycles of the System Clock
before it shuts off.
If an interrupt is triggered, the microcontroller clock will remain enabled regardless of the selected mode. As soon
as the interrupt is read the state machine will then move to the selected mode. For instance, if the chip is
commanded to Sleep mode but an interrupt has occurred the 30 MHz XTAL will not disable until the interrupt has
been cleared.
46
Add R/W
0A
R/W
Microcontroller Output Clock
Function/Description
clkt[1:0]
mclk[2:0]
00
01
10
11
000
001
010
011
100
101
110
111
D7
Preliminary Rev 0.2
D6
Modulation Source
Modulation Source
clkt[1]
D5
32.768 kHz
128 cycles
256 cycles
512 cycles
0 cycles
30 MHz
15 MHz
10 MHz
4 MHz
3 MHz
2 MHz
1 MHz
clkt[0]
D4
enlfc
D3
mclk[2] mclk[1] mclk[0]
D2
D1
D0
POR Def.
0Bh