ics1893ck-40 Integrated Device Technology, ics1893ck-40 Datasheet - Page 28
ics1893ck-40
Manufacturer Part Number
ics1893ck-40
Description
3.3-v 10base-t/100base-tx Integrated Phyceiver
Manufacturer
Integrated Device Technology
Datasheet
1.ICS1893CK-40.pdf
(121 pages)
- Current page: 28 of 121
- Download datasheet (2Mb)
6.2.3 Auto-Negotiation: Remote Fault Signaling
6.2.4 Auto-Negotiation: Reset and Restart
6.2.4.1 Auto-Negotiation Reset
6.2.4.2 Auto-Negotiation Restart
ICS1893CK-40, Rev. C, 06/02/09
If the remote link partner detects a fault, the ICS1893CK-40 reports the remotely detected fault to the STA
by setting to logic one the Remote Fault Detected bit(s), 1.4, 5.13, 17.1, and 19.13. In general, the
reception of a remote fault means that the remote link partner has a problem with the integrity of its receive
channel.
Similarly, if the ICS1893CK-40 detects a link fault, it transmits a remote fault-detected condition to its
remote link partner. In this situation, the ICS1893CK-40 sets to logic one the Auto-Negotiation Link Partner
Ability Register’s Remote Fault Indication bit (bit 4.13).
For details, see
If enabled, execution of the ICS1893CK-40 auto-negotiation process occurs at power-up and upon
management request. There are two primary ways to begin the Auto-Negotiation state machine:
•
•
During a reset, the ICS1893CK-40 initializes its Auto-Negotiation sublayer modules to their default states.
(That is, the Auto-Negotiation Arbitration State Machine and the Auto-Negotiation Progress Monitor reset to
their idle states.) In addition, the Auto-Negotiation Progress Monitor status bits are all set to logic zero. This
action occurs for any type of reset (hardware reset, software reset, or power-on reset).
As with a reset, during an Auto-Negotiation restart, the ICS1893CK-40 initializes the Auto-Negotiation
Arbitration State Machine and the Auto-Negotiation Progress Monitor modules to their default states.
However, during an Auto-Negotiation Restart, the Auto-Negotiation Progress Monitor status bits maintain
their current state. Only three events can alter the state of the Auto-Negotiation Progress Monitor status
bits after a Restart: (1) an STA read operation, (2) a reset, or (3) the Auto-Negotiation Arbitration State
Machine progressing to a higher state or value.
The Auto-Negotiation Progress Monitor Status bits change only if they are progressing to a state with a
value greater than their current state (that is, a state with a higher logical value than that of their current
state). For a detailed explanation of these bits and their operation, see
Progress
After the Auto-Negotiation Arbitration State Machine reaches its final state (which is Auto-Negotiation
Complete), only an STA read of the QuickPoll Detailed Status Register or an ICS1893CK-40 reset can alter
these status bits.
Any of the following situations initiates a restart of the ICS1893CK-40 Auto-Negotiation sublayer:
•
•
ICS1893CK-40 reset
Auto-Negotiation Restart
A link failure
In software mode:
– Writing a logic one to the Control Register’s Restart Auto-Negotiation bit (bit 0.9), which is a self-
– Toggling the Control Register’s Auto-Negotiation Enable bit (bit 0.12) from a logic one to a logic zero,
clearing bit.
and back to a logic one.
Monitor”.
ICS1893CK-40 Data Sheet - Release
Section 7.14.3, “Remote Fault (bit 19.13)”
Copyright © 2009, Integrated Device Technology, Inc.
All rights reserved.
28
and
Section 7.3.9, “Remote Fault (bit
Section 6.2.5, “Auto-Negotiation:
Chapter 6 Functional Blocks
1.4)”.
June 2009
Related parts for ics1893ck-40
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Integrated Processor
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
Integrated Riscontroller for Low-Cost Systems
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
INTEGRATED RISController FOR LOW-COST SYSTEMS
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
SwitchStar ATM Cell Based 1.2Gbps non-blocking Integrated Switch Controller
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
3.3V CMOS 16-bit bidirectional transceiver
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
3.3 CMOS octal buffer/line driver
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
Fast CMOS octal registered transceivers
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
Fast CMOS octal bidirectional transceivers
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
Fast CMOS 16-bit buffer/line driver
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
2.5 V/3.3 V 10 Bit High Bandwidth Bus Switch with Precharged Outputs
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
High-Speed CMOS Quick Switch 16:8 Multiplexer
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
QUICKSWITCH?? PRODUCTS HIGH-SPEED CMOS QUICKSWITCH DOUBLE-WIDTH BUS SWITCH IDTQS32X245Q2QUICKSWITCH PRODUCTS HIGH-SPEED CMOS QUICKSWITCH DOUBLE-WIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
2.5V / 3.3V 16-BIT HIGH BANDWIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
QUICKSWITCH PRODUCTS 2.5V / 3.3V 8-BIT HIGH BANDWIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet:
Part Number:
Description:
QUICKSWITCH PRODUCTS 2.5V / 3.3V 10-BIT HIGH BANDWIDTH BUS SWITCH
Manufacturer:
Integrated Device Technology, Inc.
Datasheet: