at89lp428-25pu ATMEL Corporation, at89lp428-25pu Datasheet - Page 35
at89lp428-25pu
Manufacturer Part Number
at89lp428-25pu
Description
8-bit Microcontroller With 4k/8k Bytes In-system Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet
1.AT89LP428-25PU.pdf
(149 pages)
- Current page: 35 of 149
- Download datasheet (5Mb)
10. I/O Ports
10.1
3654A–MICRO–8/09
Port Configuration
The AT89LP428/828 can be configured for between 23 and 30 I/O pins. The exact number of
I/O pins available depends on the package type and the clock and reset options as shown in
Table
Table 10-1.
All port pins on the AT89LP428/828 may be configured to one of four modes: quasi-bidirectional
(standard 8051 port outputs), push-pull output, open-drain output, or input-only. Port modes may
be assigned in software on a pin-by-pin basis as shown in
Table
fuse is enabled, all port pins default to input-only mode after reset. When the fuse is disabled, all
port pins, with the exception of the analog inputs, P2.4, P2.5, P2.6 and P2.7, default to quasi-
bidirectional mode after reset and are weakly pulled high. The analog input pins always reset to
input-only (tristate) mode. Each port pin also has a Schmitt-triggered input for improved input
noise rejection. During Power-down all the Schmitt-triggered inputs are disabled with the excep-
tion of P3.2 (INT0), P3.3 (INT1), P3.6 (RST), P4.0 (XTAL1) and P4.1 (XTAL2) which may be
used to wake up the device. Therefore, P3.2, P3.3, P3.6, P4.0 and P4.1 should not be left float-
ing during Power-down. In addition any pin of Port 1 configured as a GPI input will also remain
active during Power-down to wake-up the device. These interrupt pins should either be disabled
before entering Power-down or they should not be left floating.
Table 10-2.
Clock Source
External Crystal or
Resonator
External Clock
Internal RC Oscillator
PxM0.y
10-1.
10-3. The Tristate-Port User Fuse determines the default state of the port pins. When the
0
0
1
1
I/O Pin Configurations
Configuration Modes for Port x, Bit y
PxM1.y
0
1
0
1
Reset Option
External RST Pin
No external reset
External RST Pin
No external reset
External RST Pin
No external reset
Port Mode
Quasi-bidirectional
Push-pull Output
Input Only (High Impedance)
Open-drain Output
Package
PDIP
TQFP or PLCC
PDIP
TQFP or PLCC
PDIP
TQFP or PLCC
PDIP
TQFP or PLCC
PDIP
TQFP or PLCC
PDIP
TQFP or PLCC
Table 10-2
AT89LP428/828
using the registers listed in
Number of I/O Pins
23
27
24
28
24
28
25
29
25
29
26
30
35
Related parts for at89lp428-25pu
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 4K/8K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: