qt160 Quantum Research Group, qt160 Datasheet - Page 7
![no-image](/images/no-image-200.jpg)
qt160
Manufacturer Part Number
qt160
Description
6 Key Charge-transfer Qtouch? Sensor Ic
Manufacturer
Quantum Research Group
Datasheet
1.QT160.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
qt160-AS
Manufacturer:
QUANTUM
Quantity:
1 818
Part Number:
qt160-AS
Manufacturer:
QUANTUM
Quantity:
20 000
Part Number:
qt160-AS-G
Manufacturer:
QUANTUM
Quantity:
20 000
Company:
Part Number:
qt160-AS-R-G
Manufacturer:
S3
Quantity:
800
Part Number:
qt160-AS-R-G
Manufacturer:
QUANTUM
Quantity:
20 000
Company:
Part Number:
qt1608RL120HC2A-LF
Manufacturer:
TOKIN
Quantity:
4 150
3.6 ESD PROTECTION
In cases where the electrode is placed behind a dielectric
panel, the IC will be protected from direct static discharge.
However even with a panel, transients can still flow into the
electrodes via induction, or in extreme cases via dielectric
breakdown. Porous materials may allow a spark to tunnel
right through the material. Testing is required to reveal any
problems. The device does have diode protection on its SNS
pins which absorb and protect the device from most induced
discharges, up to 20mA; the usefulness of the internal
clamping will depending on the dielectric properties, panel
thickness, and rise time of the ESD transients.
In extreme cases ESD dissipation can be aided further with
added series resistors in line with the electrodes as shown in
Figure 1-1. Because the charge time is 1.2 µs, the circuit can
tolerate large values of series-R, up to 20k ohms in cases
where electrode Cx load is below 10pF. Extra diode
protection at the electrodes can also be used, but this often
leads to additional RFI problems as the diodes will rectify RF
signals into DC which will disturb the measurement.
Directly placing semiconductor transient protection devices
or MOV's on the sense leads is not advised; these devices
have extremely large amounts of nonlinear parasitic C which
will swamp the capacitance of the electrode.
Series-R’s should be low enough to permit at least 6 RC
time-constants to occur during the charge and transfer
phases, where R is the added series-R and C is the load Cx.
If the device is connected to an external control circuit via a
cable or long twisted pair, it is possible for ground-bounce to
cause damage to the Out pins and/or interfere with key
sensing. Noise current injection into the power supply is best
dealt with by shunting the noise aside to chassis ground with
capacitors, and limited using resistors or ferrites.
lQ
7
3.7 RFI PROTECTION
PCB layout, grounding, and the structure of the input circuitry
have a great bearing on the success of a design that can
withstand strong RF interference.
The circuit is remarkably immune to RFI provided that certain
design rules be adhered to:
Achieving RF immunity mostly requires diligence and a good
working knowledge of grounding, shielding, and layout
techniques.
1. Use SMT components to minimize lead lengths.
2. Always use a ground plane under and around the circuit
3. Ground planes should be connected only to a common
4. Route sense traces away from other traces or wires that
5. Sense electrodes should be kept away from other
6. Keep the 6 Cs sampling capacitors and all series-R
7. Use a 0.1µF minimum ceramic bypass cap very close to
8. Use series-R’s in the sense lines, of as large a value as
9. Bypass input power to chassis ground and again at
and along the sense lines, that is as unbroken as
possible except for relief under and beside the sense
lines to reduce total Cx. Relieved rear ground planes
should be ‘mended’ by bridging over them at 1cm
intervals with 0.5mm ‘rungs’ like a ladder.
point near the Vss pins of the IC.
are connected to other circuits.
circuits and grounds which are not directly connected to
the sensor’s own circuit ground; other grounds will
appear to float at high frequencies and couple RF
currents into the sense lines.
components close to the IC.
the QT160/161 supply pins.
the circuit can tolerate.
circuit ground to reduce line-injected noise effects.
Ferrites over the power wiring may be required to
attenuate line injected noise.
QT160/161 1.07/0904