24vl024 Microchip Technology Inc., 24vl024 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/4/440/microchip_technology_inc__sml.jpg)
24vl024
Manufacturer Part Number
24vl024
Description
2k I 2 C? Serial Eeprom
Manufacturer
Microchip Technology Inc.
Datasheet
1.24VL024.pdf
(30 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
24vl024/ST
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
24vl024H/MS
Manufacturer:
NA
Quantity:
20 000
Part Number:
24vl024H/P
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
24vl024H/SN
Manufacturer:
MCP
Quantity:
20
Part Number:
24vl024H/SN
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
24vl024H/ST
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
24vl024HT/MNY
Manufacturer:
MCP
Quantity:
20
Company:
Part Number:
24vl024T/MNY
Manufacturer:
MCP
Quantity:
20
Company:
Part Number:
24vl024T/MNY
Manufacturer:
MICROCHIP
Quantity:
12 000
Company:
Part Number:
24vl024T/ST
Manufacturer:
MICROCHIP
Quantity:
12 000
24VL024/24VL025
5.0
A control byte is the first byte received following the
Start condition from the master device (Figure 5-1).
The control byte consists of a four-bit control code; for
the 24VL024/24VL025 this is set as ‘1010’ binary for
read and write operations. The next three bits of the
control byte are the Chip Select bits (A2, A1, A0). The
Chip Select bits allow the use of up to eight 24VL024/
24VL025 devices on the same bus and are used to
select which device is accessed. The Chip Select bits
in the control byte must correspond to the logic levels
on the corresponding A2, A1 and A0 pins for the device
to respond. These bits are in effect the three Most
Significant bits of the word address.
For the SOT-23 package, the A2 pin is not connected.
During device addressing, the A2 chip select bit should
be set to logic ‘0’. Only four 24VL025 SOT-23 devices
can be connected to the same bus.
The last bit of the control byte defines the operation to
be performed. When set to a ‘1’, a read operation is
selected. When set to a ‘0’, a write operation is
selected. Following the Start condition, the 24VL024/
24VL025 monitors the SDA bus, checking the control
byte being transmitted. Upon receiving a ‘1010’ code
and appropriate Chip Select bits, the slave device
outputs an Acknowledge signal on the SDA line.
Depending on the state of the R/W bit, the 24VL024/
24VL025 will select a read or write operation.
DS22130A-page 8
DEVICE ADDRESSING
FIGURE 5-1:
5.1
The Chip Select bits A2, A1 and A0 can be used to
expand the contiguous address space for up to 16K bits
by adding up to eight 24VL024/24VL025 devices on the
same bus. In this case, software can use A0 of the
control byte as address bit A8, A1 as address bit A9,
and A2 as address bit A10. It is not possible to
sequentially read across device boundaries.
For the SOT-23 package, up to four devices can be
added for up to 8K bits of address space. In this case,
software can use A0 of the control byte as address bit
A8, and A1 as address bit A9. Bit A2 of the control byte
must always be set to logic ‘0’ for the SOT-23 package.
Start Bit
S
Contiguous Addressing Across
Multiple Devices
1
Control Code
0
Slave Address
1
CONTROL BYTE FORMAT
© 2009 Microchip Technology Inc.
0
Read/Write Bit
Chip Select
A2
Acknowledge Bit
Bits
A1
A0
R/W
ACK