lh28f128bfht-pbtl75a Sharp Microelectronics of the Americas, lh28f128bfht-pbtl75a Datasheet - Page 15

• Manufacturer Part Number: lh28f128bfht-pbtl75a
• Description: Flash Memory 16mbit 8mbitx16
• Manufacturer: Sharp Microelectronics of the Americas

NOTES:
1. Bus operations are defined in Table 4.
2. All addresses which are written at the first bus cycle should be the same as the addresses which are written at the second
3. ID=Data read from identifier codes. (See Table 3).
4. Following the Read Identifier Codes/OTP command, read operations access manufacturer code, device code, block lock
5. Block erase, full chip erase or (page buffer) program cannot be executed when the selected block is locked. Unlocked
6. Either 40H or 10H are recognized by the CUI (Command User Interface) as the program setup.
Read Array
Read Identifier Codes/OTP
Read Query
Read Status Register
Clear Status Register
Block Erase
Full Chip Erase
Program
Page Buffer Program
Block Erase and (Page Buffer)
Block Erase and (Page Buffer)
Set Block Lock Bit
Clear Block Lock Bit
Set Block Lock-down Bit
OTP Program
Program Suspend
Program Resume
bus cycle.
X=Any valid address within the device.
PA=Address within the selected plane.
IA=Identifier codes address (See Table 3).
QA=Query codes address.
BA=Address within the block being erased, set/cleared block lock bit or set block lock-down bit.
WA=Address of memory location for the Program command or the first address for the Page Buffer Program command.
OA=Address of OTP block to be read or programmed (See Figure 3).
QD=Data read from query database.
SRD=Data read from status register. See Table 9.1, Table 9.2 for a description of the status register bits.
WD=Data to be programmed at location WA. Data is latched on the rising edge of WE# or CE# (whichever
OD=Data within OTP block. Data is latched on the rising edge of WE# or CE# (whichever goes high first)
N-1=N is the number of the words to be loaded into a page buffer.
configuration code and the data within OTP block (See Table 3).
The Read Query command is available for reading CFI (Common Flash Interface) information.
block can be erased or programmed when RST# is V
goes high first) during command write cycles.
during command write cycles.
Command
Refer to Appendix of LH28F128BF series for details.
Cycles
Req’d
Bus
≥ 2
≥ 2
≥ 4
Refer to Appendix of LH28F128BF series for details.
1
2
1
2
2
2
1
1
2
2
2
2
Table 5. Command Definitions
Notes
5,9
5,6
5,7
8,9
8,9
10
4
4
5
9
LHF12F17
IH
Oper
Write
Write
Write
Write
Write
Write
Write
Write
Write
Write
Write
Write
Write
Write
Write
.
(1)
First Bus Cycle
Addr
WA
WA
BA
BA
BA
BA
OA
PA
PA
PA
PA
PA
PA
PA
X
(2)
(11)
40H or
D0H
C0H
Data
FFH
E8H
B0H
90H
98H
70H
50H
20H
30H
10H
60H
60H
60H
Oper
Write
Write
Write
Write
Write
Write
Write
Write
Read
Read
Read
(1)
Second Bus Cycle
IA or OA
Addr
WA
WA
QA
BA
BA
BA
BA
OA
PA
X
(2)
Rev. 0.04
ID or OD
Data
D0H
D0H
SRD
D0H
01H
2FH
WD
N-1
QD
OD
12
(3)