m58bw016 Numonyx, m58bw016 Datasheet - Page 34

no-image

m58bw016

Manufacturer Part Number
m58bw016
Description
16 Mbit 512 Kbit X 32, Boot Block, Burst 3 V Supply Flash Memories
Manufacturer
Numonyx
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
m58bw016BB80T3
Manufacturer:
ST
Quantity:
715
Part Number:
m58bw016BB80T3
Manufacturer:
ST
0
Part Number:
m58bw016BB80T3ES
Manufacturer:
ST
0
Part Number:
m58bw016BB80T3F
Manufacturer:
ST
Quantity:
490
Part Number:
m58bw016BB80T3F
Manufacturer:
ST
0
Part Number:
m58bw016BB80T3PT
Manufacturer:
NSC
Quantity:
2 808
Part Number:
m58bw016DB7
Manufacturer:
ST
0
Part Number:
m58bw016DB70T3
Manufacturer:
ST
Quantity:
6 975
Part Number:
m58bw016DB70T3
Manufacturer:
ST
0
Part Number:
m58bw016DB70T3F
Manufacturer:
ST
Quantity:
6 793
Part Number:
m58bw016DB70T3F
Manufacturer:
ST
Quantity:
20 000
Part Number:
m58bw016DB70T3F
Manufacturer:
ST/意法
Quantity:
800
Part Number:
m58bw016DB70T3NS
Manufacturer:
ST
Quantity:
17 246
Status register
5
5.1
5.2
34/70
Status register
The Status register provides information on the current or previous program or erase
operation. The various bits in the status register convey information and errors on the
operation. They are output on DQ7-DQ0.
To read the status register the Read Status Register command can be issued. The status
register is automatically read after Program, Erase or Program/Erase Resume commands.
The status register can be read from any address.
The contents of the status register can be updated during an erase or program operation by
toggling the Output Enable or Output Disable pins or by deactivating (Chip Enable, V
then reactivating (Chip Enable and Output Enable, V
The status register bits are summarized in
conjunction with the following text descriptions.
Program/erase controller status (bit 7)
The Program/erase controller status bit indicates whether the program/erase controller is
active or inactive. When the program/erase controller status bit is set to ‘0’, the
program/erase controller is active; when bit7 is set to ‘1’, the program/erase controller is
inactive.
The program/erase controller status is set to ‘0’ immediately after a Program/Erase Suspend
command is issued until the program/erase controller pauses. After the program/erase
controller pauses the bit is set to ‘1’.
During program and erase operations the program/erase controller status bit can be polled
to find the end of the operation. The other bits in the status register should not be tested until
the program/erase controller completes the operation and the bit is set to ‘1’.
After the program/erase controller completes its operation the erase status (bit5), program
status bits should be tested for errors.
Erase suspend status (bit 6)
The erase suspend status bit indicates that an erase operation has been suspended and is
waiting to be resumed. The erase suspend status should only be considered valid when the
program/erase controller status bit is set to ‘1’ (program/erase controller inactive); after a
Program/Erase Suspend command is issued the memory may still complete the operation
rather than entering the suspend mode.
When the erase suspend status bit is set to ‘0’, the program/erase controller is active or has
completed its operation; when the bit is set to ‘1’, a Program/Erase Suspend command has
been issued and the memory is waiting for a Program/Erase Resume command.
When a Program/Erase Resume command is issued the erase suspend status bit returns to
‘0’.
M58BW016DT, M58BW016DB, M58BW016FT, M58BW016FB
Table 11: Status register
IL
, and Output Disable, V
bits. Refer to
IH
.) the device.
Table 11
IH
) and
in

Related parts for m58bw016