uba2030t-n1 NXP Semiconductors, uba2030t-n1 Datasheet
uba2030t-n1
Related parts for uba2030t-n1
uba2030t-n1 Summary of contents
Page 1
... DATA SHEET UBA2030T Full bridge driver IC Product specification Supersedes data of 1999 Aug 10 INTEGRATED CIRCUITS 2002 Sep 27 ...
Page 2
... Adjustable oscillator frequency High voltage level shifter for the bridge enable function Shut-down function. APPLICATIONS The UBA2030T can drive the MOSFETs in any type of load configured as a full bridge The circuit is intended as a commutator for High Intensity Discharge (HID) lamps. ORDERING INFORMATION ...
Page 3
... EXO pin connected to SGND RC pin connected to SGND; f osc(ext ----------------- bridge 2 adjusted externally bridge enable active bridge enable not active V SD shut-down active; 5 V/ms ------------- - t shut-down not active V/ms ------------- - t 3 Product specification UBA2030T MIN. TYP. MAX. UNIT 0 570 V 0.7 1.0 mA 14.0 15.5 17.0 V 11.5 13.0 14.5 V 140 190 240 mA 200 260 320 ...
Page 4
... BE 7 BRIDGE ENABLE HIGH VOLTAGE LEVEL SHIFTER OSCILLATOR UBA2030T 2 LOW VOLTAGE LOGIC LEVEL SHIFTER EXO DTC SD Fig.1 Block diagram. 4 Product specification UBA2030T 10 FSL 11 HIGHER LEFT GHL DRIVER 12 SHL 15 FSR 14 HIGHER RIGHT GHR DRIVER 13 SHR 3 LOWER LEFT GLL DRIVER ...
Page 5
... DD SGND 24 signal ground 2002 Sep 27 handbook, halfpage GLR 1 PGND 2 GLL 3 n. n.c. 6 UBA2030T BE 7 BER 8 n.c. 9 FSL 10 GHL 11 SHL 12 Fig.2 Pin configuration. 5 Product specification UBA2030T 24 SGND DTC EXO 19 n. n.c. 16 n.c. 15 FSR GHR 14 SHR 13 MGK589 ...
Page 6
... SGND to obtain a ripple-free internal DD supply voltage. Start-up When the power is turned on, the UBA2030T enters a start-up phase; the high side MOSFETs are switched off and the low side MOSFETs switched on. During start-up, the bootstrap capacitors are charged and the bridge output current is zero ...
Page 7
... Philips Semiconductors Full bridge driver IC on handbook, full pagewidth V BE off GHL V GLR V GHR V GLL 2002 Sep 27 dead time Fig.3 Timing diagram. 7 Product specification UBA2030T time MGK594 ...
Page 8
... V. FSL FSR PARAMETER 8 Product specification CONDITIONS MIN 570 V, note 1 570 = 570 1250 1500 VALUE UBA2030T MAX. UNIT 18 V 570 V 588 +570 V +10 V 570 V 580 700 ...
Page 9
... 500 Hz bridge FSR FSL source FSR FSL sink source sink diode 9 Product specification UBA2030T MIN. TYP. MAX. UNIT 0 570 0.7 1 14.0 15.5 17.0 V 11.5 13.0 14.5 V 2.0 2.5 3.0 V 0.5 0.7 mA 15.3 16 ...
Page 10
... V EXO 5 V/ms ----------------- t V EXO 5 V/ms ----------------- t adjusted externally bridge enable active note 6 bridge enable not active I = 100 Product specification UBA2030T MIN. TYP. MAX. UNIT 140 190 240 mA 200 260 320 50000 0.67 0.71 0.75 0.01 2.34 2 ...
Page 11
... M with low leakage current. osc(max) ) connected between pins DTC and SGND. The value is DT 70, where the units are k for DT(max 150 C. BE BER j 11 Product specification UBA2030T MIN. TYP. 4 V/ 150 C. j and s for t . The minimum value DT dead MAX ...
Page 12
... R and C osc supply voltage exceeds the ‘start oscillating threshold’ (typically 15.5 V). If the supply voltage at the HV pin falls below the ‘stop oscillating threshold’ (typically 13 V), the UBA2030T enters the start-up state. SHR SHL 13 12 GHR GHL ...
Page 13
... MOSFETs in the full bridg SHR SHL 13 12 GHR GHL FSR FSL BER 18 8 EXO BE UBA2030T DTC GLL PGND 2 23 SGND GLR Fig.5 External control configuration. 13 Product specification UBA2030T HL C1 IGNITOR LAMP MGK593 ...
Page 14
... GHR GHL FSR FSL BER 18 8 EXO BE 20 UBA2030T DTC GLL PGND 23 2 SGND GLR osc Fig.6 Automotive configuration (example 1). 14 Product specification UBA2030T HL C1 IGNITOR LAMP osc HR LR MGK591 ...
Page 15
... Philips Semiconductors Full bridge driver IC Additional application information The UBA2030T is the commutator part in a complete system for driving an HID lamp. The life of the HID lamp can depend on the amount of sodium that migrates through its quartz wall. To minimize this migration, the lamp must be operated negative with respect to system ground ...
Page 16
... REFERENCES JEDEC EIAJ MS-013 detail 1.1 1.1 1.4 0.25 0.25 0.4 1.0 0.043 0.043 0.055 0.01 0.01 0.016 0.039 EUROPEAN PROJECTION Product specification UBA2030T SOT137 ( 0.9 0.1 0 0.035 0.004 0.016 ISSUE DATE 97-05-22 99-12-27 ...
Page 17
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 17 Product specification UBA2030T ...
Page 18
... Wave soldering is suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 2002 Sep 27 (1) not suitable not suitable suitable not recommended not recommended 18 Product specification UBA2030T SOLDERING METHOD (2) WAVE REFLOW suitable (3) suitable suitable (4)(5) suitable ...
Page 19
... Product specification UBA2030T DEFINITIONS These products are not Philips Semiconductors ...
Page 20
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2002 All rights are reserved. Reproduction in whole or in part is prohibited ...