t6816-tiq ATMEL Corporation, t6816-tiq Datasheet
t6816-tiq
Available stocks
Related parts for t6816-tiq
t6816-tiq Summary of contents
Page 1
... SO28 Power Package Description The T6816 is a fully protected driver interface designed in 0.8 µm BCDMOS technol- ogy especially suitable for truck or bus applications and the industrial 24-V supply. It controls different loads via a 16-bit dataword. Each of the six high-side and six low-side drivers is capable to drive currents up to 600 mA ...
Page 2
... Input Register 24 CS Output Register INH Fault Fault Detect Detect 16 LS1 LS2 T6816 2 HS3 HS4 Fault Fault Detect Detect ...
Page 3
... LS6 DI CLK CS GND GND GND Lead frame GND GND GND LS5 HS5 HS4 LS4 VS GND VCC DO INH T6816 GND VS LS3 HS3 = 2 MHz) max T6816 LS1 HS1 HS2 LS2 3 ...
Page 4
... CLK and stay stable until the next rising edge of CLK appears. LSB (bit 0, TP) is transferred first. Figure 3. Data Transfer Input Data Protocol CS DI SRR LS1 HS1 CLK DO TP SLS1 SHS1 SLS2 Table 1. Input Data Protocol T6816 4 LS2 HS2 LS3 LS4 HS3 HS4 SHS2 SLS3 SHS3 SLS4 SHS4 ...
Page 5
... Power supply fail: undervoltage at Pin VS detected Note: Bit high: overtemperature shutdown Bit 11 Bit 10 Bit 9 Bit 8 Bit 7 (LS6) (HS5) (LS5) (HS4) (LS4 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 (HS3) (LS3) (HS2) (LS2) (HS1 T6816 Bit 1 Bit 0 (LS1) (SRR ...
Page 6
... SCD bit is set. By writing a high to the SRR bit in the input register, the SCD bit is reset and the disabled outputs are enabled. Inhibit There are two ways to inhibit the T6816: 1. Set bit SI in the input register to zero 2. Switch Pin 17 (INH both cases, all output stages are turned off but the serial interface stays active ...
Page 7
... Min. Typ. R thJP R thJA Min. Typ. ( 4.5 5 VCC V -0.3 INH, DI, V CLK CLK T -40 j T6816 Unit °C °C Max. Unit 25 K/W 65 K/W Max. Unit VCC 2 MHz ° ...
Page 8
... Thermal prewarning *) Type means: A =100% tested 100% correlation tested Characterized on samples Design parameter Notes: 1. Delay time between rising edge of CS after data transmission and switch on output stages to 90% of final level T6816 8 Test Conditions ISO 7637-1 VDE 0879 Part 2 MIL-STD-883D Method 3015.7 EOS/ESD - S 5.2 < ...
Page 9
... I LS1–6 11,14 16, 27 Min. Typ. Max. 20 jPW 150 170 190 130 150 170 20 1.05 1.17 1.05 1.2 1.5 2 LS1-6 10 -10 15 outx /dt 50 200 400 /dt 650 950 1250 T6816 Unit Type °C A ° µA A µ mV/µ ...
Page 10
... V CS Pin CS *) Type means: A =100% tested 100% correlation tested Characterized on samples Design parameter Notes: 1. Delay time between rising edge of CS after data transmission and switch on output stages to 90% of final level T6816 10 < 150°C; unless otherwise specified, j Pin Symbol HS1– ...
Page 11
... CSSethl t 225 CSSetlh t 16 CSh t 2 CSh t 225 CLKh t 225 CLKl t 500 CLKp t 225 CLKSethl t 225 CLKSetlh t 40 DIset t 40 DIHold T6816 Unit Type µA A Max. Unit 200 ns 200 ns 100 ns 100 ns 200 ...
Page 12
... Figure 4. Serial Interface Timing with Chart Numbers CLK 3 DI CLK DO Inputs DI, CLK, CS: High level = 0 Output DO: High level = 0 T6816 low level = 0 CC, , low level = 0 4595B–BCD–05/03 ...
Page 13
... GND Control GND UV - protection logic 9 GND Thermal protection GND Power-on Reset 21 GND Vcc 22 GND Fault Fault 23 GND Detect Detect Vcc 19 Vcc LS5 LS6 T6816 BYT41 V D BAT 24V Vcc Vcc 5 V and V as close ...
Page 14
... Ordering Information Extended Type Number T6816-TIQ Package Information Package SO28 Dimensions in mm 0.4 1. T6816 14 Package SO28 18.05 17.80 2.35 0.25 0.10 16. Remarks Power package, taped and reeled 9.15 8.65 7.5 7.3 0.25 10.50 10.20 technical drawings according to DIN specifications 4595B–BCD–05/03 ...
Page 15
... Atmel Corporation 2003. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein ...