a8286 Allegro MicroSystems, Inc., a8286 Datasheet - Page 10
![no-image](/images/no-image-200.jpg)
a8286
Manufacturer Part Number
a8286
Description
Dual Lnb Supply And Control Voltage Regulator
Manufacturer
Allegro MicroSystems, Inc.
Datasheet
1.A8286.pdf
(19 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
a8286SETTR
Manufacturer:
ALLEGRO/雅丽高
Quantity:
20 000
Part Number:
a8286SETTR-T
Manufacturer:
ALLEGRO/雅丽高
Quantity:
20 000
Part Number:
a8286SLB
Manufacturer:
ALLEGRO/雅丽高
Quantity:
20 000
A8286
tion. If the Read/Write bit is high, the master reads the contents of
register 1, followed by register 2 if a further read is performed. If
the Read/Write bit is low, the master writes data to one of the four
Control registers. Note that multiple writes are not permitted. All
write operations must be preceded with the address.
to determine if the slave device is responding to its address and
data, and it is used by the slave when the master is reading data
back from the slave. When the A8286 decodes the 7-bit address
field as a valid address, it responds by pulling SDA low during the
ninth clock cycle.
low during the clock cycle that follows the data byte, in order to
A8286 always responds by resetting the data transfer sequence.
The Read/Write bit is used to determine the data transfer direc-
The Acknowledge bit has two functions. It is used by the master
During a data write from the master, the A8286 also pulls SDA
Figure 3. I
SDA
SCL
Start
2
C™ Interface. Read and write sequences.
0
1
0
2
SDA
SCL
SDA
SCL
0
3
Start
Start
Address
1
4
Dual LNB Supply and Control Voltage Regulator
0
1
0
1
0
5
A1
0
2
0
2
6
A0
Read Multiple Bytes from Register
0
3
0
3
7
Address
Address
Read One Byte from Register
R
1
4
1
4
1
8
AK
0
5
0
5
9
acknowledge
from LNBR
A1
A1
D7
6
6
Write to Register
A0
A0
D6
7
7
Status Data in Register 1
D5
W
R
0
8
1
8
AK
AK
D4
9
9
acknowledge
from LNBR
acknowledge
from LNBR
indicate that the data has been successfully received. In both cases,
the master device must release the SDA line before the ninth clock
cycle, in order to allow this handshaking to occur.
same way as in the data write sequence, and then retains control
of the SDA line and send the data from register 1 to the master.
On completion of the eight data bits, the A8286 releases the SDA
line before the ninth clock cycle, in order to allow the master to
acknowledge the data. If the master holds the SDA line low dur-
ing this Acknowledge bit, the A8286 responds by sending the data
from register 2 to the master. Data bytes continue to be sent to the
master until the master releases the SDA line during the Acknowl-
edge bit. When this is detected, the A8286 stops sending data and
waits for a stop signal.
D7
D3
I1
During a data read, the A8286 acknowledges the address in the
D6
D2
I0
D5
D5
D1
Status Register 1
Control Data
D4
D4
D0
D3
D3
AK
acknowledge
from LNBR
D2
D2
-
D1
D1
-
Status Data in Register 2
D0
D0
-
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
NAK
AK
-
acknowledge
from LNBR
no acknowledge
from master
Stop
Stop
D3
D2
D1
D0
NAK
no acknowledge
from master
Stop
10