attiny25v ATMEL Corporation, attiny25v Datasheet - Page 155
attiny25v
Manufacturer Part Number
attiny25v
Description
Microcontroller With 2/4/8k Bytes In-system Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet
1.ATTINY25V.pdf
(231 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
attiny25v-10MU
Manufacturer:
ATMEL
Quantity:
1 650
Part Number:
attiny25v-10MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
attiny25v-10PU
Manufacturer:
Atmel
Quantity:
29 497
Company:
Part Number:
attiny25v-10PU
Manufacturer:
Atmel
Quantity:
5 000
Company:
Part Number:
attiny25v-10SU
Manufacturer:
ATMEL
Quantity:
2 110
Part Number:
attiny25v-10SU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
attiny25v-15ST
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
- Current page: 155 of 231
- Download datasheet (5Mb)
20.5
2586K–AVR–01/08
Serial Downloading
Both the Flash and EEPROM memory arrays can be programmed using the serial SPI bus while
RESET is pulled to GND. The serial interface consists of pins SCK, MOSI (input) and MISO (out-
put). See below.
Figure 20-1. Serial Programming and Verify
Notes:
After RESET is set low, the Programming Enable instruction needs to be executed first before
program/erase operations can be executed.
Table 20-10. Pin Mapping Serial Programming
Note:
When programming the EEPROM, an auto-erase cycle is built into the self-timed programming
operation (in the Serial mode ONLY) and there is no need to first execute the Chip Erase
instruction. The Chip Erase operation turns the content of every memory location in both the
Program and EEPROM arrays into 0xFF.
Depending on CKSEL Fuses, a valid clock must be present. The minimum low and high periods
for the serial clock (SCK) input are defined as follows:
Low: > 2 CPU clock cycles for f
High: > 2 CPU clock cycles for f
1. If the device is clocked by the internal Oscillator, it is no need to connect a clock source to the
In
pins dedicated for the internal SPI interface.
Symbol
MOSI
MISO
Table 20-10
SCK
CLKI pin.
above, the pin mapping for SPI programming is listed. Not all parts use the SPI
MOSI
MISO
SCK
Pins
PB0
PB1
PB2
ck
ck
< 12 MHz, 3 CPU clock cycles for f
< 12 MHz, 3 CPU clock cycles for f
RESET
GND
(1)
I/O
O
I
I
VCC
+1.8 - 5.5V
ATtiny25/45/85
ck
ck
Serial Data out
Serial Data in
Description
Serial Clock
>= 12 MHz
>= 12 MHz
155
Related parts for attiny25v
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: