attiny25v ATMEL Corporation, attiny25v Datasheet - Page 45
attiny25v
Manufacturer Part Number
attiny25v
Description
Microcontroller With 2/4/8k Bytes In-system Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet
1.ATTINY25V.pdf
(231 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
attiny25v-10MU
Manufacturer:
ATMEL
Quantity:
1 650
Part Number:
attiny25v-10MU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
attiny25v-10PU
Manufacturer:
Atmel
Quantity:
29 497
Company:
Part Number:
attiny25v-10PU
Manufacturer:
Atmel
Quantity:
5 000
Company:
Part Number:
attiny25v-10SU
Manufacturer:
ATMEL
Quantity:
2 110
Part Number:
attiny25v-10SU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
attiny25v-15ST
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
- Current page: 45 of 231
- Download datasheet (5Mb)
8.4.1
8.4.1.1
8.4.1.2
2586K–AVR–01/08
Timed Sequences for Changing the Configuration of the Watchdog Timer
Safety Level 1
Safety Level 2
“Timed Sequences for Changing the Configuration of the Watchdog Timer” on page 45
details.
Table 8-1.
Figure 8-7.
The sequence for changing configuration differs slightly between the two safety levels. Separate
procedures are described for each level.
In this mode, the Watchdog Timer is initially disabled, but can be enabled by writing the WDE bit
to one without any restriction. A timed sequence is needed when disabling an enabled Watch-
dog Timer. To disable an enabled Watchdog Timer, the following procedure must be followed:
In this mode, the Watchdog Timer is always enabled, and the WDE bit will always read as one. A
timed sequence is needed when changing the Watchdog Time-out period. To change the
Watchdog Time-out, the following procedure must be followed:
WDTON
Unprogrammed
Programmed
1. In the same operation, write a logic one to WDCE and WDE. A logic one must be writ-
2. Within the next four clock cycles, in the same operation, write the WDE and WDP bits
1. In the same operation, write a logical one to WDCE and WDE. Even though the WDE
2. Within the next four clock cycles, in the same operation, write the WDP bits as desired,
ten to WDE regardless of the previous value of the WDE bit.
as desired, but with the WDCE bit cleared.
always is set, the WDE must be written to one to start the timed sequence.
but with the WDCE bit cleared. The value written to the WDE bit is irrelevant.
WDT Configuration as a Function of the Fuse Settings of WDTON
Watchdog Timer
Safety
Level
1
2
WATCHDOG
OSCILLATOR
RESET
128 kHz
WDP0
WDP1
WDP2
WDP3
WDE
WDT Initial
State
Disabled
Enabled
How to Disable the
WDT
Timed sequence
Always enabled
MCU RESET
PRESCALER
WATCHDOG
ATtiny25/45/85
How to Change Time-
out
No limitations
Timed sequence
for
45
Related parts for attiny25v
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: