adm9240 Analog Devices, Inc., adm9240 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
adm9240
Manufacturer Part Number
adm9240
Description
Low Cost Microprocessor System Hardware Monitor
Manufacturer
Analog Devices, Inc.
Datasheet
1.ADM9240.pdf
(22 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
adm9240-1A
Manufacturer:
AD
Quantity:
5 510
Company:
Part Number:
adm9240-1A
Manufacturer:
MOT
Quantity:
5 510
Company:
Part Number:
adm9240A
Manufacturer:
AD
Quantity:
5 510
Company:
Part Number:
adm9240ARN
Manufacturer:
AD
Quantity:
5 510
Company:
Part Number:
adm9240ARN
Manufacturer:
LT
Quantity:
5 510
Part Number:
adm9240ARU
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
adm9240ARUZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
ADM9240
When reading data from a register there are two possibilities:
1. If the ADM9240’s Address Pointer Register value is un-
2. If the Address Pointer Register is known to be already at the
Notes:
1. Although it is possible to read a data byte from a data register
known or not the desired value, it is first necessary to set it to
the correct value before data can be read from the desired
data register. This is done by performing a write to the
ADM9240 as before, but only the data byte containing the
register address is sent, as data is not to be written to the
register. This is shown in Figure 2b.
A read operation is then performed consisting of the serial
bus address, R/W bit set to 1, followed by the data byte read
from the data register. This is shown in Figure 2c.
desired address, data can be read from the corresponding
data register without first writing to the Address Pointer
Register, so Figure 2b can be omitted.
without first writing to the Address Pointer Register, if the
Address Pointer Register is already at the correct value, it is
not possible to write data to a register without writing to the
Address Pointer Register, because the first data byte of a
write is always written to the Address Pointer Register.
SDA
SCL
SDA
SCL
START BY
START BY
MASTER
MASTER
1
0
1
0
1
1
SERIAL BUS ADDRESS BYTE
SERIAL BUS ADDRESS BYTE
0
0
Figure 2c. Reading Data from a Previously Selected Register
Figure 2b. Writing to the Address Pointer Register only
1
FRAME 1
FRAME 1
1
1
1
A1
A1
A0
A0
R/ W
R/ W
ADM9240
ACK. BY
ADM9240
ACK. BY
9
9
–8–
D7
D7
2. In Figures 2a to 2c, the serial bus address is shown as the
ANALOG INPUTS
The ADM9240 has six analog inputs. Four of these are dedi-
cated to monitoring the following power supply voltages: +12 V,
+5 V, +3.3 V, +2.5 V.
These inputs are multiplexed into the on-chip, successive ap-
proximation, analog-to-digital converter. This has a resolution
of ten bits, but only eight bits are used for the voltage measure-
ment and limit comparison. The basic input range of the ADC
is 0 V to 2.5 V, and the power supply inputs are scaled by on-
chip attenuators such that the ADC produces an output of 3/4
full scale or 192 decimal, when the input voltage is at its nomi-
nal value. The use of on-chip scaling guarantees accuracy and
removes the need for precision external resistors.
1
1
default value 01011(A1)(A0), where A1 and A0 are
hardwired to either Logic 0 or Logic 1.
D6
D6
ADDRESS POINTER REGISTER BYTE
D5
D5
DATA BYTE FROM ADM9240
D4
D4
FRAME 2
FRAME 2
D3
D3
D2
D2
D1
D1
D0
D0
BY MASTER
ADM9240
ACK. BY
NO ACK.
9
9
STOP BY
MASTER
STOP BY
MASTER
REV. 0