ftlf1421s1xcl Finisar Corporation., ftlf1421s1xcl Datasheet
ftlf1421s1xcl
Related parts for ftlf1421s1xcl
ftlf1421s1xcl Summary of contents
Page 1
... Single 3.3V power supply Low power dissipation <700 mW typical Extended operating temperature range: -10°C to 70°C Finisar’s FTLF1421S1xCL Small Form Factor (SFF) transceivers are compatible with the Small Form Factor Multi-Sourcing Agreement (MSA) 48 IR-1 (SDH STM S-16.1) standards 3 specified in IEEE Std 802.3 , Fibre Channel FC-PI 13.0 ...
Page 2
... FTLF1421S1XCL 2x10 Pin SFF Product Specification – December 2003 I. Pin Descriptions Pin Symbol MS MS Mounting Studs for mechanical attachment. Chassis ground is internally isolated from circuit ground. Connection to chassis ground is recommended Receiver Power Monitor. This pin must be connected to a positive voltage supply (Vcc), preferably via a small resistor ...
Page 3
... FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 II. Absolute Maximum Ratings Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity Lead Soldering Temperature/Time III. Electrical Characteristics Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing ...
Page 4
... FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 IV. Optical Characteristics Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width –20dB Optical Extinction Ratio Sidemode Supression ratio Optical Rise/Fall Time Relative Intensity Noise Total Generated Transmitter Jitter (peak to peak) ...
Page 5
... FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 V. General Specifications Parameter Data Rate Bit Error Rate @ OC-48 Max. Supported Link Length on 9/125 m SMF @ OC-48 Max. Supported Link Length on 9/125 m SMF @ 2X Fibre Channel Max. Supported Link Length on 9/125 m SMF @ Gigabit Ethernet Max. Supported Link Length on 9/125 m SMF @ OC-12 Max ...
Page 6
... FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 VIII. Analog Diagnostics Functions Parameter Transmitter Monitor photodiode current monitor Laser bias current monitor Receiver Received photocurrent Photodiode responsivity Applied voltage at PD pin Notes: 1. Pins 19 and 20 provide an analog voltage output proportional to the monitor photodiode current, per the following formula: I equivalent circuit ...
Page 7
... FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 IX. Mechanical Specifications Finisar’s OC-48/STM-16 Small Form Factor (SFF) transceivers comply with the standard dimensions defined by the Small Form Factor Multi-Sourcing Agreement (MSA). FTLF1421S1GCL (dimensions are in inches) – 2 pin version Finisar Corporation March, 2006 Rev A ...
Page 8
... FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 FTLF1421S1HCL (dimensions are in inches) – 6 pin version Finisar Corporation March, 2006 Rev Page 8 ...
Page 9
... FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 FTLF1421S1HCL – 6 pin version (Long EMI Shield) Finisar Corporation March, 2006 Rev Page 9 ...
Page 10
... FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 X. PCB Layout and Bezel Recommendations Minimum Recommended Pitch is 0.600” Finisar Corporation March, 2006 Rev Page 10 ...
Page 11
... Note AN-2038: Finisar Implementation of RoHS Compliant Transceivers:. Finisar Corporation, January 21, 2005. (*) Neither IEEE 802.3 nor FC-PI 13.0 specifies a 1310nm DFB single mode interface. The FTLF1421S1XCL complies with these standards except for receiver sensitivity, and transmit output power. See Section IV for details. XII. ...
Page 12
... FTLF1421S1XCL 2x10 Pin SFF Product Specification – March 2006 Finisar Corporation March, 2006 Rev Page 12 ...